User manual LIFT-MASTER EL MODELS QUICK START GUIDE

[. . . ] Click the Unit Configuration ICON and Select the CONTROL SETTINGS Tab EL MODEL Quick Start Guide For Single Family Residence No Phone Line (Without Directory Codes) Installation using Versa XS 1 Enter Unit Name and Unit Type 1 2 Enter Country, State/Prov. and City 2 Click on the "Edit" button Uncheck the "Use Telephone Service" check box This Quick Start is intended to highlight a typical single family home with one phone line. [. . . ] Click the TRANSFER DATA ICON Check the "Use This Connect Set for Unit" check box 5 Click "Test It" then click OK 1 Check Configuration and Tenant Info in the Send Data to Unit frame 1 Wait for Versa XS to identify modems 2 1 2 3 3 Select a Connect Set from the "Connect Set" list 4 Click OK A pop-up window will inform you that the Connect Set was sucessfully tested. NOTE: If "Test It" button fails, try one of the following: 1. Check the appropriate Connection Mode (Direct or Modem) type confirms with the selected COM port (see you computer's COM settings). Close any other application using the COM port. If the problem persists, please call technical support. 5 1 2 2 Click START NOTE: If a mismatch message/warning appears click OK. ® 1. Click the NEW UNIT ICON EL MODEL Quick Start Guide For Multi-Family or single-Family (With Directory Codes) Versa XS 1 Enter Unit Name and select the correct Unit Type 2 3 4 5 2 Enter Country, State/Prov. , City and Phone Number Enter Phone Number to dial into unit 3 This Quick Start is intended to highlight a typical Multi-Tenant Complex. These instructions are not intended to be comprehensive. Each application is unique, it is the responsibility of the purchasers, designer, installer and end user to ensure that the total control access system is safe for its intended use. Please refer to the manuals and/or qualified technician for further information. 4 Click OK 2. Click the Unit Configuration ICON Select the DEVICES Tab Rename "Device 1" to "Back Door Reader" Disabled 1 1 2 Choose "RF Receiver" for "J407" 3 Choose "Wiegand Device" for "J400" 6 Click on the "Device Configuration Wizard" button 2 Rename "Device 3" to "Gate Receiver" 3 4 5 6 Disabled 4 Click OK 3. Click the DOORS Tab 3 1 Rename "Door 1" to "Front Door" Rename "Door 2" to "Back Door" and select "Back Door Reader" for the Device 5 Rename "Door 3" to "Gate" and select "Back Door Reader" for the Device 1 Set Relay Names, Relay Types and Activation Times: Relay Name Front Strike Security Light Back Strike Gate Relay Type Relay Activation Time Strike Control Strike Strike 10 Seconds 60 Seconds 10 Seconds 2 Seconds 1 2 2 2 1 4 3 6 7 5 Relay # 1 2 3 4 Select "Front Door Group" from the drop-down menu 4 Select "Back Door Group" from the drop-down menu 6 Select "Gate Group" from the drop-down menu Click SAVE 2 Set Relay Groups: Back Strike X X Gate Relay Group Name Front Strike Security Light Front Door Group X X Back Door Group Gate Group 7 6. Click the ACCESS DETAILS Tab Enter Last Name 2 Enter Display Info 1 2 1 2 1 Enter an Entry Code (optional) 2 Click on Select and create a new Credential (optional) NOTE: The unit uses Display Info for transactions when the Entry Code or Credential Code is used. NOTE: A credential is a generic term when referring to a transmitter or swipe card. 7. [. . . ] Close any other application using the COM port. If the problem persists, please call technical support. 5 1 2 2 Click START NOTE: If a mismatch message/warning appears click OK. 114A3000C © 2006 Chamberlain Elite All Rights Reserved [. . . ]