User manual LIFT-MASTER FDCL C

[. . . ] LM PL C C O N OWNER'S MANUAL MODEL FDCL C ADVANCED LOGIC INDUSTRIAL DUTY FIRE DOOR OPERATOR LMPLC CONTROL TR O L WIRED 2 YEAR WARRANTY NOT FOR RESIDENTIAL USE Serial # Box (located on electrical box cover) Installation Date Wiring Type FM APPROV APP OVED TABLE OF CONTENTS SPECIFICATIONS Operator Specifications . . 3 CONTROL SETTINGS Optional Control Settings . . 13 Optional Mechanical (Retrofit) Fuse Link Arrangement . . 14 THEORY OF OPERATION General Description. [. . . ] It is imperative that the alarm signal contact is maintained for a time period greater than the alarm delay to close setting. If dip switch #1 is in the "OFF" position (10 seconds) the alarm system must supply a "DRY" contact signal to terminals J2-11 and J2-12 for a minimum of 12 seconds. Alarm Input #2: Used for the thermal sensors (electronic fusible links), fuse link kit or similar systems. state only) The sensor or similar system must supply a "DRY N. C. " contact signal. This alarm condition will activate a motored closure of the door (except in Fire Door Mode Type II), and all sensing devices and control stations will be rendered inactive. This alarm will override any other alarm condition or input. WARNING To avoid SERIOUS PERSONAL INJURY or DEATH: · It is the end users sole responsibility to check that ALL systems are installed and functional. · The motor operator MUST be switched to the "firedoor mode type 1" to enable ALL alarm and warning systems. · DIP switch #2 MUST be switched to the "ON" position to enable the "firedoor" mode. Failure to do so, could result in loss of life and property. CAUTION 9 TIMIL ESOLC YRAILIXUA TIMIL ESOLC TIMIL YRAILIXUA ERAPS TIMIL NEPO TIMIL ESOLC YRAILIXUA TIMIL ESOLC TIMIL YRAILIXUA ERAPS TIMIL NEPO ING ON POWER WIRING & GROUND WIRING WARNING WARNING To reduce the risk of SEVERE INJURY or DEATH: · DISCONNECT and LOCK-OUT power BEFORE installation or performing ANY maintenance to the operator or in the area near the operator. Upon completion of maintenance the area MUST be cleared and secured BEFORE returning the operator to service. · Operator MUST be properly grounded and connected in accordance with local electrical codes. The operator should be on a separate fused line of adequate capacity. · Operator MUST be permanently wired as per NFPA 70 (National Electrical Code) ground MUST be pulled with each service. Service voltage MUST be run separately from class 2 circuits. · To avoid damage to door and operator, make ALL door locks inoperative. Secure lock(s) in "open" position. If the door lock needs to remain functional, install an interlock switch. Remove the cover from the electrical enclosure. Inside this enclosure you will find the wiring diagram(s) for your unit. Refer to the diagram (glued on the inside of the cover) for all connections described below. If this diagram is missing, see contact information on page 28. · ALL electrical connections MUST be made by a qualified individual. [. . . ] Sign Label Door Edge Caution Label Reset Label Rating Label (L1, L2, L3) Warning Label Keystation Warning Label QTY 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 K75-16515 LIMIT SWITCH ASSEMBLY KIT ITEM S1 S2 S3 S4 S5 S6 S7 PART # MOTOR ASSEMBLY KIT ITEM M1 M2 M3 DESCRIPTION Coupling-L-Jaw Coupling-Spider Motor, 1/2HP 115/230V (1 Phase Units) 20-3050B-4F Motor, 1/2HP 230/460V (3 Phase Units) 84-FN-25 Flange Nut, 1/4" PART # 07-17247 07-17483 20-1050B-2F QTY 2 1 1 11-17209 12-10028 13-10024 15-25B12AXX 80-10022 86-RP04-100 87-E-038 DESCRIPTION Limit Shaft Bearing Flange Limit Nut Sprocket, 25B12 Spacer Roll Pin, 1/8" E-Ring QTY 1 2 2 1 2 1 2 CHARGING CIRCUIT BOARD UPGRADE KIT - INCLUDES UPGRADE CHIP, PCB BATTERY BOARD AND BATTERIES PART # K29-FDCL-500CCB DESCRIPTION Upgrade compatible for operators with 102 and 400 firmware M4 4 K20-1050B-2F K20-1050B-2F MODELS: FDLC501124V, FDLC502124V MODELS: FDLC501124V, FDLC502124V COVER ASSEMBLY ITEM C1 C2 C3 C4 PART # 07-17067 10-17234 40-16485 82-PX06-06 DESCRIPTION Cover Plate Identification UL Caution Label Screw, #6-32 QTY 1 1 1 4 20 I L L U S T R AT E D PA R T S - E L E C T R I C A L B O X 20 19 18 3 13 C2 C1 C3 M3 5 6 M4 M1 7 8 9 C4 M2 22 17 2 14 10 12 15 15 1 See pages 22 and 23 21 4 16 21 REPAIR PARTS KITS - MODEL FDCL C Refer to the parts lists below for replacement kits available for your operator. If optional modifications and/or accessories are included with your operator, certain components may be added or removed from these lists. Individual components of each kit may GEAR HOUSING ASSEMBLY ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 PART # 10-17062 10-17063 10-17064 19-25047M 19-35047M 31-17219 31-17220 31-17221 82-HN25-08 84-FN-25 85-LS-25 07-17201 07-17202 11-17069 12-17205 80-17360 80-207-22 82-NH31-06 87-E-062 07-17200 11-17070 12-17204 80-17360 82-NH31-06 87-E-050 07-17203 11-17071 12-17206 15-35B13GGF 80-17628 80-17629 82-NH25-06 82-NH31-06 87-E-075 11-17068 12-10715 15-25B25LGF 15-35B40LGF 80-10022 80-10023 80-17632 80-17633 82-NH25-06 87-E-100 DESCRIPTION Main Side Plate Output Side Plate Spur Gear Side Plate Chain, #25 x 47 Links Chain, #35 x 47 Links Standoff, 5. 312 Long Standoff, 3. 625 Long Standoff, 1. 562 Long Hex Bolt 1/4 x 1/2" Flange Nut, 1/4" Lockwasher, 1/4" Spur Gear, 12 DP 18 Spur Gear, 16 DP 64 Reduction Shaft Flanged Bearing, 5/8" Key, 3/16" x 3/4" Key, 3/16" x 1" Set Screw, 5/16 x 3/8" E-Ring, 5/8" Spur Gear 16 DP 16 governor Shaft Flanged Bearing 1/2" Key, 3/16" x 3/4" Set Screw, 5/16 x 3/8" E-Ring, 1/2" Spur Gear 16 DP 60 RPM Shaft Flanged Bearing Sprocket, 5/16 Key, 3/16" x 1-1/4" Key, 3/16" x 1/2" Set Screw, 1/4-20 Set Screw, 5/16 x 3/8" E-Ring 3/4" Output Shaft Bearing Sprocket, 25B25 Sprocket, 35B40 Spacer Spacer Key, 1/4" x 1/4" Key, 1/4" x 1/2" Set Screw, 1/4-20 E-Ring, 1" QTY 1 1 1 1 1 2 4 2 6 15 6 1 1 1 2 1 2 4 4 1 1 2 1 2 3 1 1 2 1 1 1 2 2 4 1 2 1 1 1 1 1 1 4 3 22 ITEM L1 L2 L3 L4 L5 L6 L7 L8 L9 L10 L11 L12 L13 L14 not be available. Please consult a parts and service representative regarding availability of individual components. [. . . ]