User manual LIFT-MASTER Q411

[. . . ] Part # Q411 CSW / SL Surge Protection Module Please read this entire manual before installation Chamberlain Professional Products strongly recommends the installation of this Surge Protection Module to protect the gate operator from harmful surges caused by lightning strike phenomenon. It is important to recognize that the surge protection module may not prevent damage to the gate operator in the event of a direct lightning strike. [. . . ] Never splice two wires for the ground wire. If you should cut the ground wire too short, break it, or destroy its integrity, replace it with a single wire length. 8 ft Chamberlain Professional Products, Inc. is not responsible for improper installation or failure to comply with all necessary local building codes. ® TM CSW / SL Surge Protection Module STEP 1 Turn the gate operator off by turning off the building/facility breaker for the 120 Vac supply to the gate operator. Refer. Bus 1, 2, 3 Step-by-Step instructions STEP 2 Remove J1 plug. Air (1) Conditioner Main Room Conference Rm 2, 3 On Conference Room 2 Off Conference Room 1 On Off Off On Off Off Off On Gate Operator Eug. 1 Rm 1 2 3 4 5 6 7 8- 9 10 + Fire Dep Key Switch Strike Open or Push Button Safety Loop Or Photocell Exit Loop Radio Receiver Off Comp. 2 Rm STEP 3 Remove the wire nuts from the black and white wires (16 AGW) coming from the plug . STEP 4 Remove all the accessory wires attached to the terminal block. Make sure to mark all the wires you are removing to reconnect them later. 1 2 3 4 5 6 7 8- 9 10 + Fire Dep Key Switch Strike Open or Push Button Safety Loop Or Photocell Exit Loop Radio Receiver 1 2 3 4 5 6 7 8- 9 10 + Fire Dep Key Switch Strike Open or Push Button Safety Loop Or Photocell Exit Loop Radio Receiver STEP 5 Use a nut driver and remove the 2 hex nuts holding the terminal block connector (10 terminals) on the electrical box. STEP 6 Remove the terminal block connector from the electrical box. 1 2 3 4 5 6 7 8- 9 10 + Fire Dep Key Switch Strike Open or Push Button Safety Loop Or Photocell Exit Loop Radio Receiver 1 2 3 4 5 6 7 8- 9 10 + Fire Dep Key Switch Strike Open or Push Button Safety Loop Or Photocell Exit Loop Radio Receiver STEP 7 Place the Surge Protector module in place of the terminal block. Use a nut driver to secure the 2, 1 inch long hex nuts that came with the module. STEP 8 There is a green wire with a ring terminal coming out of the Surge Protection module, This ring terminal MUST make good contact with the chassis of the gate operator. ® CSW / SL Fire Dep SURGE Key Switch SUPPRESSOR P/N Q411 ­ PATENT PENDING 1 2 3 4 5 6 7 8- 9 10 + Strike Open or Push Button Safety Loop Or Photocell Exit Loop + ­ Radio Receiver SAFTEY LOOP EXIT LOOP STRIKE OPEN FIRE DEPT KEY SWITCH PUSH BUTTON RADIO RECEIVER CLASS 2 SUPPLY Remove the control board and unscrew the lower left hex nut under the board. Slip the ring terminal on the screw stud. Make sure ring is in contact with the control box. Re-screw the hex nut and re-attach the control board. ® CSW / SL SURGE SUPPRESSOR P/N Q411 ­ PATENT PENDING SAFTEY LOOP EXIT LOOP STEP 9 Reconnect the accessory wires to the Surge Protector. Match them up with the label on the module. [. . . ] The shield must be connected as follows: A) At the gate operator: To the chassis of the gate operator B) At the accessories: To their chassis (Earth grounding at the accessories will be even more beneficial) Ensure that the connections to the chassis are made secure to create good contact. ® 01-50739 © 2005 The Chamberlain Group, Inc. All Rights Reserved For Technical Support: 1-800-528-2806 TM 845 Larch Avenue Elmhurst, Illinois 60126 www. chamberlain. com [. . . ]