User manual LIFT-MASTER SL1000-B3(168)

[. . . ] ESTATE SERIES B3 MODEL SL 1000-B3 INSTALLATION MANUAL HEAVY DUTY, HIGH CYCLE SLIDE GATE OPERATOR MODEL SL 1000-B3 IS FOR VEHICULAR PASSAGE GATES ONLY, NOT INTENDED FOR PEDESTRIAN PASSAGE GATE USE 3 YEAR WARRANTY Serial #______________________ (located on electrical box) Installation Date ______________ Page 1 of 48 Doc 01-20202 Rev J TABLE OF CONTENTS TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SAFETY SUMMARY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 BASIC INSTALLATION HINTS AND RULES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PART 1 SITE PREPARATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 A. LOCATION AND LAYOUT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PAD AND MOUNT. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . POWER WIRING. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Activate the CYCLE command, wait until the gate is fully open, then activate the CYCLE command again. The gate should close, verifying Alternate Action operation. Note: If you select Alternate Action, you cannot use ATG = ON and TIMER = ON in procedures 7 and 8 that follow. Reclose Timer (RT) If TIMER switch S1-1 has been set to ON and Reclose Timer pot R94 has been adjusted, verify Reclose Timer action as follows: 1. Activate any entry command (except Manual OPEN) to open the gate. Start timing when the gate reaches fully open and verify that the Reclose Timer recloses the gate after the desired interval. NOTE: Reclose Timer is not functional when the Manual OPEN command is used. Page 22 of 48 Doc 01-20202 Rev J 8. Inside Interrupt Loop and ATG (Anti-Tailgating when exiting) GATE TYPE IS SLIDE ATG OFF: If ATG switch S1-2 has been set to OFF, activate the CYCLE command, drive over the Interrupt Loop and verify its operation: !Opening Gates: When a vehicle drives on the Interrupt Loop an opening gate will be unaffected. Closing Gates: When a vehicle drives on the Interrupt Loop a closing gate will open and the Reclose Timer (if enabled) will start. ATG ON: If ATG switch S1-2 has been set to ON, activate the CYCLE command, drive over the Interrupt Loop and verify its operation: !Opening Gates: When a vehicle drives on the Interrupt Loop an opening gate will continue to open, but will close as soon as the vehicle drives off the Interrupt Loop. Closing Gates: When a vehicle drives on the Interrupt Loop a closing gate will stop, but will close as soon as the vehicle drives off the Interrupt Loop. Figure 19. Photo-Sensors (Secondary Obstruction Sensing per UL325 Requirements Refer to the figure above for Photo-Sensor coverage areas. Coverage Area A: While the gate is opening, put your hand or arm through the Inside PhotoSensor beam. The gate should restart when the obstruction (your hand) is removed. Coverage Area B: Stand inside the fence line. While the gate is closing, put your hand or arm through the Outside Photo-Sensor beam. The gate should restart when the obstruction (your hand) is removed. Coverage Area C: Stand outside the fence line. While the gate is closing, put your hand or arm through the Outside Photo-Sensor beam. The gate should restart when the obstruction (your hand) is removed. Page 23 of 48 Doc 01-20202 Rev J 10. [. . . ] These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: 1. [. . . ]