User manual LIFT-MASTER SL575

[. . . ] CO NT RO LL ER GL BO AR D MODEL SL575 HEAVY DUTY SLIDE GATE OPERATOR 2 YEAR WARRANTY Serial # ________________________ (located on electrical box cover) Installation Date __________________ MODEL SL575 IS FOR VEHICULAR PASSAGE GATES ONLY AND IS NOT INTENDED FOR PEDESTRIAN PASSAGE GATE USE TABLE OF CONTENTS OPERATOR SPECIFICATIONS Carton Inventory . . 2 Operator Dimensions & Horsepower Chart . . 4 WARNING Mechanical OPERATOR WARNINGS Safety Installation Information . . 5 Suggested Entrapment Protection Device Locations . [. . . ] TIMER TO CLOSE ENABLE This switch enables the auto close timer. The timer to close feature works in conjunction with the potentiometer located on the board. TIMER TO CLOSE ENABLED SAVE TTC ON ON 1 2 SL 3 LT 4 1 2 SL 3 LT 4 S1 SW RT TIMER TO CLOSE DISABLED SAVE TTC ON ON S1 SW RT TIMER TO CLOSE Max = 180 sec Min = 0 sec SLIDE/SWING This switch selects slide or swing gate operation, in order to optimize gate behavior for specific application. SL = Slide · SW = Swing RIGHT/LEFT OPERATION This switch selects the gate opening direction, to the left or to the right. Right/Left operation is determined from the inside of fence looking out. SWING GATE SAVE TTC ON ON 1 2 SL TTC ON ON 1 2 SL 3 LT 4 SW 3 LT SAVE 4 S1 SW RT RT SLIDE GATE SAVE TTC ON ON 1 2 SL 3 LT 4 S1 SW RT RIGHT HAND S1 LEFT HAND SAVE TTC ON ON 1 2 SL 3 LT 4 S1 SW RT "SAVE" SWITCH LOCKED SAVE TTC UNLOCKED SAVE TTC S1 S1 SW RT SW RT This switch stores all settings into memory and locks out changes. NOTE: For any programming changes to take effect this switch must be in OFF position. When switch is ON, no settings can be changed. ON APEMs ON ON ON 1 2 SL 3 LT 4 1 2 SL 3 LT 4 PROGRAM SETTINGS (DIP SWITCH S2) MAGLOCK ENABLE MAGLOCK ENABLED WARN CLED OPED MAG MAGLOCK DISABLED WARN CLED OPED MAG S2 This switch enables the Maglock feature. On an open command there will be a half second delay after the maglock relay is released before the motor starts. S2 ON ON 1 2 3 PH 4 PH ON ON 1 2 3 PH 4 PH WARNING ENABLE WARNING ENABLED WARN CLED OPED MAG WARNING DISABLED WARN CLED OPED MAG S2 This switch enables the gate "in motion" alarm feature. The alarm will beep 3 seconds prior to movement and throughout movement. S2 ON ON 1 2 3 PH 4 PH ON ON 1 2 3 PH 4 PH 17 CONTROL CONNECTION DIAGRAMS Accessory Terminal Block Accessory Terminal Block 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 24VAC Accessory Power May Be Found On These Terminals R1 R2 R3 R4 24 VAC Override Open Input (N. O) Control Board Override Close Control Input (N. O. ) OPEN 123 56 789 0# CLOS E ST OP Override Open Control Input (N. O) OPEN CLOS E Stop/Reset Control Input (N. C. ) OPEN ST OP SINGLE PHASE BOX NOTE: See wiring diagrams shipped with kit for additional information. See owner's manual for wiring distances and wire gauge information. WARNING: All controls that are to be used to operate the gate system, must be installed where the user cannot come into contact with the gate while operating the controls where the user has full view of gate operation. *We strongly recommend that you follow the UL guidelines presented throughout the manual. Installation device instructions: Always follow the instructions provided by the manufacturer when installing and adjusting any control device. If these instructions are contrary to the advice given here, call for assistance. CLOS E ST OP Interrupt (Safety) Loop Input (N. O) Shadow Loop Input (N. O. ) RF QE RF QE Obstruction While Opening Edge/Photo Eye Input (N. O. ) Radio (Single Button) Input (N. O. ) Obstruction While Closing Edge/Photo Eye Input (N. O. ) 18 ACCESSORY WIRING All inputs are normally open and momentary, except the stop (N. C. ). The following instructions are based upon UL325, and include recommendations for significant increase in safety. The GL operator employs 24VDC "High" control signalling. Meaning the input is not common, but is 24VDC. Take precautions when wiring any type of surge protection. We strongly recommend that you follow the UL guidelines presented throughout the manual. Refer to instructions shipped with optional control devices for mounting, wiring, programming and adjustment. 24VAC Accessory Power can be found at terminals R1 and R2 located on radio terminal block. The LiftMaster Radio Receiver comes pre-wired to the Operator · Remove the brass antenna from the accessory box and screw it onto the "F"-connector provided on the side of the gate operator. NOTE: The radio receiver is wired in the factory for single button control to open and close the gate. R1 R2 R3 R4 24VAC RADIO RCVR. Receiver Operator Terminal 4 3 Connector Antenna R4 R3 R2 R1 Relay Control 24VAC Power 2 1 Accessory Tray 1 234567 REMOTELY MOUNTED STOP/RESET CONTROL WIRING · This control will function as a Stop/Reset command and is to be wired within line of sight of the gate. [. . . ] warrants to the first retail purchaser of this product, for the structure in which this product is originally installed, that it is free from defect in materials and/or workmanship for a period of two years from the date of purchase. The proper operation of this product is dependent on your compliance with the instructions regarding installation, operation, maintenance and testing. Failure to comply strictly with those instructions will void this limited warranty in its entirety. If, during the limited warranty period, this product appears to contain a defect covered by this limited warranty, call 1-800-528-2806, toll free, before dismantling this product. [. . . ]