User manual LIFT-MASTER STAR450-315

[. . . ] · Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. · ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. This device complies with FCC Rules Part 15 and IC Canada Rules and Regulations. Operation is subject to the following two conditions: (1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. [. . . ] Remote Antenna Mounting: Use the optional 86LM antenna extension kit to mount the remote antenna as high and far from metal as possible for best radio range (Figure 2). Contact LiftMaster customer service at: 1-800-528-2806 to order the model 86LM. Figure 1 Antenna Seal Boot Antenna Connector Figure 2 STAR450 FEATURES POWER INDICATOR SCROLLING DASHES ON DIGITAL DISPLAY WHEN AC OR DC POWER IS APPLIED TO THE UNIT. DIGITAL DISPLAY DISPLAYS REMOTE CONTROL LOCATION NUMBERS WHEN PROGRAMMING OR ACCESS IS GRANTED. ALSO DISPLAYS USER PROMPTS AND MESSAGES. DELETE KEY USED TO DELETE A REMOTE CONTROL FROM THE SELECTED MEMORY LOCATION ANTENNA CONNECTION FOR CONNECTION TO THE DIRECT ANTENNA OR THE ANTENNA EXTENSION KIT. BLOCK KEY USED TO BLOCK THE RECEIVER FROM GRANTING ACCESS TO THE SELECTED REMOTE CONTROL. REMOTE CONTROL REMAINS IN MEMORY, AND MAY BE UNBLOCKED IN THE FUTURE. Add ADD KEY USED TO ENTER REMOTE CONTROLS AND ENTER RAPID LEARNTM MODE. Delete Block 1 4 7 * 2 5 8 0 3 6 9 # NUMERIC KEYPAD USED FOR PROGRAMMING AND QUERYING REMOTE CONTROL LOCATIONS. ALSO USED TO ENTER ADVANCED FUNCTIONS. STAR KEY USED TO ENTER ADVANCED FUNCTIONS: , 1- LAST REMOTE CONTROL RECEIVED , 2- NO. OF BLOCKED REMOTE CONTROL LOCATIONS , 5- FIRST BLOCKED REMOTE CONTROL LOCATION , 7- SOFTWARE VER. # , 0- AUDIBLE DIAGNOSTICS OFF/ON POUND KEY USED AS AN ESC OR EXIT KEY FOR ALL FUNCTIONS OR MODES. PROGRAMMING THE STAR450 Rapid LearnTM: Add remote control to next available location. AUTO 001 Add PRESS PRESS # PRESS TO EXIT Add Adding Remote Control: Add remote control to a specific location. AUTO 001 Add PRESS 002 2 023 3 234 4 PRESS # PRESS TO EXIT ENTER LOCATION (1-450) Add Deleting a Remote Control: To delete a user. Del Delete PRESS 002 2 023 3 234 4 Delete PRESS TO CONFIRM Del END ENTER LOCATION (1-450) 2 PROGRAMMING THE STAR450 (CONT'D) Blocking (Unblocking) a Remote Control: To block or unblock a user. bLc Block PRESS 002 2 023 3 234 4 Block PRESS TO CONFIRM bLc END (UNBLOCK) ENTER LOCATION (1-450) Un- bLc Duplicating Memory: Allows user to backup programmed remote control memory into the provided backup memory module. Note: If two memory modules are installed, press , 6 to duplicate the memory and remove the backup module. Main Memory Module dup , PRESS SIMULTANEOUSLY Backup Memory Module * 6 END ~6 SECONDS Note: To duplicate memory, plug backup memory module into backup slot and press , 6. Once duplication is complete, remove the backup memory module and store in a separate location. Restoring Memory: To restore memory, simply place the duplicate memory module in the main memory position. ADVANCED FUNCTIONS For advanced functions, press and hold the key and a number key at the same time to select the corresponding advanced function. (See table at right for available functions. ) Press the # key to exit the function. * 1 Memory location of last remote control received. * 3 # of blocked remote control locations. * 5 5 Next blocked location (Repeat to scroll). Duplicate * 6 Version # memory- See Duplicating memory. * 0 Audible diagnostics OFF/ON (LED will be displayed when OFF) If no remote controls are programmed into the star450, then (---) will be displayed. AUDIBLE DIAGNOSTICS Step 1. (LED will be displayed when OFF) Double Beep: Remote control is valid and programmed into STAR450 accompanied by remote control location display. Slow Beep: Security+® Remote control (Not programmed in STAR450). [. . . ] Delete unused transmitters from memory 2. Verify transmitter is listed in compatible transmitters section Or 3. Replace transmitter battery Replace main memory module Replace backup memory module No beep when transmitting Transmitter does not activate operator Transmitter will not learn into memory Unit does not function, Main memory module missing or damaged [E 1] displayed Duplication function does not work, [E 2] displayed Keypad does not respond, [E 3] displayed Backup memory module missing or damaged, if included Keypad has a stuck key Cycle power. If unit exhibits this condition again after 2 minutes, contact Technical Service. ELECTRICAL CONNECTIONS FOR STAR450 Receiver (Bottom) Wall Button Receiver (Bottom) Wall Button Opener Trans Primary Trans Primary Model 85 Transformer To wall outlet To wall Model 95 outlet Transformer STAR450 COMPATIBLE REMOTE CONTROLS Security+® Remote Controls 371LM 372LM 370LM 373LM 374LM STAR450 OPTIONAL ACCESSORIES CGI Part Number 71-65WTBOX 86LM 85LM 95LM Security+® Keypads 376LM Description Watertight Box Field Install Kit Antenna Extension Kit 24VAC Transformer with Barrel Connector 24VAC Transformer with Screw Terminals PassportTM Remote Control CPT43 CPT13 CPT23 CPT33 Digital Remote Controls 361LM 362LM 363LM HOW TO ORDER REPAIR PARTS OUR LARGE SERVICE ORGANIZATION SPANS AMERICA INSTALLATION AND SERVICE INFORMATION ARE AVAILABLE 6 DAYS A WEEK. [. . . ]