User manual LIFT-MASTER SW420

[. . . ] GL CO NT RO LL ER BO AR D MODEL SW420 LIGHT DUTY SWING GATE OPERATOR 2 YEAR WARRANTY Serial # ________________________ (located on electrical box cover) Installation Date __________________ MODEL SW420 IS FOR VEHICULAR PASSAGE GATES ONLY AND IS NOT INTENDED FOR PEDESTRIAN PASSAGE GATE USE TABLE OF CONTENTS OPERATOR SPECIFICATIONS Carton Inventory . . 4-5 IMPORTANT NOTE · BEFORE attempting to install, operate or maintain the operator, you MUST read and fully understand this manual and follow all safety instructions. · These instructions are intended to highlight certain safety related issues. These instructions are not intended to be comprehensive. [. . . ] The following instructions are based upon UL325, and include recommendations for significant increase in safety. We strongly recommend that you follow the UL guidelines presented throughout the manual. Refer to instructions shipped with optional control devices for mounting, wiring, programming and adjustment. Field Wiring Terminal Blocks R1 R2 R3 R4 3 5 5 8 9 10 11 12 J1 Terminal Block 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 SW420 Operator 24Vac Accessory PowerCan be found at terminals R1 & R2 located on radio terminal block. R1 R2 R3 R4 GL Board 24 Vac J1 Terminals 1 & 5 - Residential Radio (single button) Input These terminals are intended for use with a radio receiver in a residential application or as a single button control. This allows the user to open the gate by activating the transmitter when the gate is closed or between limits. This input also gives the user the ability to close the gate by activating the transmitter when the gate is on the open limit. J1 Terminals 2 & 5 - Shadow Loop Input These terminals are intended for use with a loop detector and is primarily used on swing gate operators. This input protects cars by preventing the gate from moving off of the open or close limit when the shadow loop input is active. RESIDENTIAL RADIO (SINGLE BUTTON) INPUT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 SHADOW LOOP INPUT 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 RF QE J1 Terminals 6 & 5 - Soft Open These terminals are intended for use as a general open control. Accessories that may be wired to this input include: Telephone Entry Systems, Radio Receiver (Commercial Applications), Exit Loop Detector, Keypads, 7-Day Timer. Note: Will not override a double entrapment (signalled by the gate stopped and entrapment alarm on). 123 56 789 0# SOFT OPEN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 RF QE Field Wiring Terminals 8 & 5 - Interrupt (Safety) Loop Input These terminals are intended for use with a loop detector. This input functions to reverse a closing gate to the open limit. Latching this input will reset the timer to close. INTERRUPT (SAFETY) LOOP INPUT 5 8 9 10 11 12 RF QE 19 OPTIONAL CONTROL DEVICES Field Wiring Terminals 9 & 5 - Obstruction Open (Edge/ Photo Eye Input) Edge Input: See Programming Section This input will reverse an opening gate to the close limit. Activating this input when the gate is closing will have no effect. Note: If upon reversal a second seperate obstruction is detected (gate edge or R. P. M. Photo Eye Input: See Programming Section This input will pause an opening gate. Once the input (photo eye) is cleared, the gate continues to open. Activating this input when the gate is closing will have no effect. Field Wiring Terminals 10 & 5 - Obstruction Close (Edge/ Photo Eye Input) Edge Input: See Programming Section This input will reverse a closing gate to the open limit. When reaching the open limit the timer to close, if enabled, will be disabled until another command is given. Activating this input when the gate is closing will have no effect. Note: If upon reversal a second seperate obstruction is detected (gate edge or R. P. M. Photo Eye Input: See Programming Section This input will reverse a closing gate to the open limit. This input will not affect the timer to close. [. . . ] CLOSE 24 VAC-COMMON (W) DC-GND (RD) LOCK 1 LOCK 1 3 OPTION FI ELD WIRING R1 R2 R3 R4 3 5 5 8 9 10 11 12 24 VAC RADIO SIGNAL STOP INTERRUPT LOOP R1 ALARM 1 ALARM 1 ENTRAPMENT OPEN ENTRAPMENT CLOSE SEE NOTE 4 J4 DUAL GATE 1 2 TO PRIMARY/SECONDARY UNIT NOTES: 1) TRANSFORMER PRIMARY VOLTAGE SAME AS OPERATOR LINE VOLTAGE 24V SECONDARY 15VA. 2) TERMINAL DESIGNATIONS SHOWN FOR 115V ONLY. 4) (B+) AND (B-) ARE 100db SAFETY ALARMS. 5) CONNECTED INTERNALLY ON GL PC BOARD APPLICATIONS: CONTROL WIRING TYPE - GL FIELD WIRING & ADJUSTMENTS MODEL TYPES: HORSEPOWER: VOLTAGE/PHASE: DRAWING NUMBER: SW420 1/3 115V & 230V - 1 PHASE ONLY REV: 845 Larch Avenue, Elmhurst, IL 60125 G1977 C 31 NOTES 32 NOTES 33 NOTES 34 WARRANTY POLICY Seller warrants that the goods are free from defect in materials and/or workmanship for a period of two years from the date of shipment from the F. O. B. [. . . ]