User manual LIFT-MASTER T

[. . . ] LO G IC OWNER'S MANUAL MODEL T LOGIC CONTROL (VER. 2. 0) INDUSTRIAL DUTY DOOR OPERATOR L PATENT PENDING C O N TR O L FACTORY SET C2 Wiring See pages 15 and 16 for other wiring configurations The Maintenance Alert System TM allows the installer to set an internal Maintenance Cycle Counter. An LED on the 3-button station will signal when the set number of cycles is reached or when the opener requires immediate service. 2 YEAR WARRANTY NOT FOR RESIDENTIAL USE Serial # (located on electrical box cover) Installation Date Wiring Type LISTED DOOR OPERATOR 41B6 Before attempting to install, operate or maintain the operator, you must read and fully understand this manual and follow all safety instructions. These instructions are intended to highlight certain safety related issues. [. . . ] If the Timer To Close has been activated, the open button and radio control can recycle the timer. The stop button will deactivate the timer until the next command input. The Timer to Close will function from the programmable mid-stop with this wiring type. (NOTE: Requires Optional self monitoring photo eyes to operate. ) FSTS Momentary button contact for open, close and stop. Radio controls allowing open, close and stop. The single button station opens the door to the full open limit bypassing the mid stop and activates the Timer To Close, putting the operator in TS mode until the door reaches the down limit, or is stopped in travel. At which time the operator enters the B2 mode. (NOTE: Requires Optional self monitoring photo eyes to operate. ) ON ON T 1 2 3 4 OFF ON ON FSTS 1 2 3 4 OFF ON ON C2 FAIL SAFE 1 2 3 4 C2 Failsafe 3 Button, 3 Button Radio Control Same functions as C2. Self Monitoring safety device must be installed to operate door. See Self Monitoring Safety Device Options below. OFF ON ON B2 FAIL SAFE 1 2 3 4 B2 Failsafe 3 Button, 1 Button, 1 & 3 Button Radio Control Same functions as B2. Self Monitoring safety device must be installed to operate door. See Self Monitoring Safety Device Options below. OFF ON ON D1 FAIL SAFE 1 2 3 4 D1 Failsafe 2 Button, 3 Button Radio Control Same functions as D1. Self Monitoring safety device must be installed to operate door. See Self Monitoring Safety Device Options below. OFF ON ON E2 Failsafe 2 Button, 3 Button Radio Control Same functions as E2. Self Monitoring safety device must be installed to operate door. See Self Monitoring Safety Device Options below. E2 FAIL SAFE 1 2 3 4 OFF SELF MONITORING SAFETY DEVICE OPTIONS To use the operator in any of the Failsafe wiring modes, or Timer To Close wiring modes (TS, T, FSTS), a LiftMaster self monitoring safety device must be installed. Recommended LiftMaster Self Monitoring Safety Devices: CPS-L NEMA 1 Direct Connect Eyes CPS-LN4 NEMA 4 Direct Connect Eyes NOTE: 1. External interlocks may be used with all functional modes. Auxiliary devices are any devices that have only dry contacts. Examples are: photocell, loop detector, pneumatic or electrical treadles, radio controls, one button stations, pull cords, etc. Open override means that the door may be reversed while closing by activating an opening device without the need to use the stop button first. 16 STANDARD PROGRAMMING FEATURES RPM Sensor/Auxiliary Reversal System (Programming is Recommended) Feature: By programming the RPM sensor to a specific application, the logic board learns the speed the door travels with reference to the spinning motor. [. . . ] Refer to page 23 for all repair part ordering information. Electrical Box Replacement Kits To order a complete electrical box kit, add a K- prefix to the model number of your operator. For example: T5011L (Operator) = K-T5011L (Electrical box replacement kit) Electrical Box Sub-Assemblies K72-13912 Limit Shaft Assembly K72-12514 Limit Switch Assembly Motor Kits K20-1033B2L Models T3311L, T3321L K20-3033B4 Models T3323L, T3338L, T3343L K20-51033B Model T3325L K20-1050B2L Models T5011L, T5021L K20-3050B4 Models T5023L, T5038L, T5023L K20-51050B Model T5025L K20-1075B2 Models T7511L, T7521L K20-3075B4 Models T7523L, T7538L, T7543L K20-51075B Model T7525L K20-1100B2T Models T1011L, T1021L K20-3100B4T Models T1023L, T1043L Shaft Assemblies K72-12506 Clutch Shaft Assembly (1/3 & 1/2 HP Models) K72-12507 Clutch Shaft Assembly (3/4 & 1HP Models) K72-12508 Output Shaft Assembly (1/3 & 1/2 HP Models) K72-12509 Output Shaft Assembly (3/4 & 1 HP Models) Hardware, Track, Drive Chain Kits K77-13821 Hardware Kit See pg. 19 Track Brake Kits 71-B120 115 Volt Models 71-B240 230-460 Volt Models * COMPLETE ELECTRICAL BOX KITS Item 1 2 3 4 5 6 7 8 9 10 P/N 10-13790 10-10115 21-XXXX 25-XXXX 79-13433 42-10040 75-13705 79-15016 093D0148 29-CDO-XXX Description Electrical Box Electrical Box Cover (See Variable Components) (See Variable Components) PCB assembly Terminal Block, Radio Standoff, Assembly RPM Sensor Board Housing, RPM Board Programmed Chip Qty 1 1 1 1 1 1 9 1 1 1 * Electrical Box Kits include parts from K72-13912 and K72-12514 K72-13912 Item L1 L2 L3 L4 L5 L6 L7 L8 L9 P/N 11-10021 12-10028 13-10024 15-48B9A 80-10025 80-10026 86-RP05-108 87-E-038 29-10344 LIMIT SHAFT ASSEMBLY KIT Description Limit Shaft, Standard T Flange Bearing, 3/8" I. D. [. . . ]