User manual LINE 6 M13 STOMPBOX MODELER PILOT HANDBOOK REV C

[. . . ] ® M13 Stompbox Modeler Pilot's Handbook Manuel de pilotage Pilotenhandbuch Pilotenhandboek Manual del Piloto See www. line6. com/manuals for Advance Guide 40-00-0167 AdvancedUsersGuideavailable@www. line6. com/manuals RevC Important Safety Instructions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT REMOVE SCREWS. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THE APPLIANCE TO RAIN OR MOISTURE. CAUTION: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. [. . . ] Step on a footswitch to activate that memory. Step on an active memory switch to bypass the FX Unit. some Filter effects. For Delay and MOD effects turn the second top row knob or for Filters turn the first bottom row knob of the FX Unit all the way to max, and you'll switch between tap tempo and regular control modes. Once you're in Tap tempo control mode, turn the knob to select one of the available note values. Tap 2 or more times on the TAP switch, and all the effects set to tap tempo control will change their time/speed/ tempo to match the tempo you tapped. To end tap tempo operation for an effect, turn the knob to max again. NOTE: Parameters set to tap tempo control are NOT affected by expression pedal operation. TAP - Tap tempo is available for all Delay effects, most MOD effects, and sCenes & sCene setup You can run your M13 Stompbox Modeler in Scene Select Mode giving you 12 scenes, each of which is a complete pedalboard, storing all the settings of the A/B/C memories of the 3 FX Units. In addition to all the FX settings, a scene stores the signal position of the send/return loop, BPM, DSP/True bypass, Gate, plus the expression pedal assignments, so those can change with each scene. We've loaded each scene with an example pedalboard, to get you inspired. SwampThing AZ Still Brings It My ScratchPad Scene Zepplica Call The Police Bridge Of Vibes On The Edge `Road' Suitcase Bass In Your Face DL Mania Jeff-O-MATIC Expression Pedals! switch from one set of multiple effects to another. Bypass all FX units by stepping on the active scene footswitch. To save your current set of FX Units settings to a scene or to copy your currently loaded Scene from normal operation, holding SCENES initiates scene save: Scene names are shown in the displays, with current scene inverted and flashing. Press an A/B/C footswitch to select a scene to replace, and now just that display is lit, showing just the that scene name. You can change the name by turning the MODEL SELECT knob to change the selected character. Turning the upper right parameter knob chooses other characters for editing. SCENES light is flashing: hold it for at least 2 seconds to complete the save (or step on LOOPER CONTROLS or TAP to abandon saving). Scene Save To access your Scenes, step on the SCENES footswitch. Your displays will now show the names of all 12 available scenes. The currently active Scene is shown in the solid circle (AZ Still Brings IT in the example above) and its corresponding footswitch will be lit. To select a different Scene, press any of the other 11 FX Unit Footswitches. Momentary Scene Mode is the default setting, so selecting a new scene puts you right into a whole new pedal board where you can turn effects off and on. Scene Folders Momentary Scene Mode In Momentary Scene Mode, once you select a new Scene your display will then return to the basic operation view. You can now activate or bypass any FX Unit if you would like. Any changes you make to the Scene will automatically be saved, just like a traditional pedalboard setup. To select a new Scene, simply step on the SCENES footswitch and choose a new scene. Your M13 is equipped with 4 scene folders giving you a total of 48 scenes. To access a new folder press the scene button and then turn FX Unit 1's Model Select knob and select the folder you wish to load (1-4) then press any scene to load it. [. . . ] Relative / Absolute Pots - Contrast - (upper right) adjusts the brightness of the displays. DIM ON/OFF (lower right) enables the dimly lit footswitch LED's when effect memories are bypassed (on) or disables them (off). In REL mode when you turn a knob the parameters will not jump to the position of the knob but change proportionally to the amount of your parameter knob movement up or down. When set to ABS it is not possible to make incremental edits of an effect parameter. The parameter value always adjusts from the current pot position. FX Lp - The hardware send/return loop can be routed before all the FX Units, or after any of them. [. . . ]