User manual LINKSYS EF1324 Install Guide

[. . . ] Instant EtherFast® Series EtherFast® Layer 3 Management 24-Port 10/100 + 2-Port Gigabit Ethernet Switch Use this guide to install: EF1324 User Guide EC Declaration of Conformity (Europe) In compliance with the EMC Directive 89/336/EEC, Low Voltage Directive 73/23/EEC, and Amendment Directive 93/68/EEC, this product meets the requirements of the following standards: · EN55022 Emission · EN55024 Immunity Industry Canada (Canada) This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe (B) est conforme à la norme NMB-003 du Canada. COPYRIGHT & TRADEMARKS Copyright © 2002 Linksys, All Rights Reserved. EtherFast, Linksys, and the Linksys logo are registered trademarks of Linksys. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation. [. . . ] Select Add to add a virtual link. 66 67 Instant EtherFast® Series EtherFast® Layer 3 Management 24-Port 10/100 + 2-Port Gigabit Ethernet Switch OSPF Host Route Configuration The OSPF Host Route Configuration screen allows you to configure the OSPF host route parameters. Add OSPF Host Route The Add OSPF Host Route screen allows you to add an OSPF host route. · · IP Address - The IP address applied for this interface. Cost - The cost of sending a packet on the interface, expressed in the link state metric. Area ID - The OSPF area to which the attached network belongs to. · · IP Address - The IP address applied for this interface. Cost - The cost of sending a packet on the interface, expressed in the link state metric. Area ID - The OSPF area to which the attached network belongs to. · · Select Apply to make changes. Select OK to return to the previous panel. Select Prev Page to view the previous page. To display a specific page, set the page number in the Page field and then press Apply. Select Add to add a host route. Select OK to return to the previous panel. Select Cancel to cancel any changes. 68 69 Instant EtherFast® Series EtherFast® Layer 3 Management 24-Port 10/100 + 2-Port Gigabit Ethernet Switch BOOTP Relay Database Configuration The BOOTP Relay Database Configuration screen allows you to specify the IP address for a BOOTP relay server. IGMP Snooping Configuration The IGMP Snooping Configuration allows you to set up IGMP snooping. IGMP snooping is used to monitor for any attached hosts who want to receive a specific multicast service. It looks up the IP Multicast Group used for this service and adds any port that received a similar request to that group. (This is the screen and options displayed for a Switch in multilayer mode. ) · Index Server Address - Used to define any preferred DHCP servers or the outbound subnetwork for relaying a DHCP request broadcast. (Up to five entries are permitted. ) Select OK to return to the previous panel. Add BOOTP Relay Server The Add BOOTP Relay Server screen allows you to add an entry. · · IGMP Router Timeout - A switch port that stops receiving multicast protocol packets for this interval will be removed from the IGMP forwarding list. IGMP Group Timeout - The time between last spotting an IGMP Report message for an IP multicast address on a specific port and the Switch removing that entry from its list. The range is 3-5 minutes. Select Apply to make changes. Select OK to return to the previous panel. Select Cancel to cancel any changes. · IP Address - IP address of server. Select OK to return to the previous panel. Select Cancel to cancel any changes. 70 71 Instant EtherFast® Series EtherFast® Layer 3 Management 24-Port 10/100 + 2-Port Gigabit Ethernet Switch Static ARP Table The Static ARP Table screen is used to specify the static Address Resolution Protocol. Add Static ARP Entry The Add Static ARP Entry screen is used to add a static ARP entry. · · IP Address - IP address statically mapped to a physical MAC address. · MAC Address - MAC address statically mapped to the corresponding IP address. [. . . ] Spanning-tree detects and directs data along the shortest path, maximizing the performance and efficiency of the network. Static Routing - Forwarding data in a network via a fixed path. Static routing cannot adjust to changing line conditions as can dynamic routing. Subnet Mask - The method used for splitting IP networks into a series of subgroups, or subnets. [. . . ]