User manual LINKSYS WET610N

[. . . ] 15 Wireless Security Checklist Change the default wireless network name or SSID Change the default password Enable MAC address filtering Enable encryption Status > Bridge . 13 i Linksys WES610N/WET610N Product Overview Product Overview Thank you for choosing the Linksys Dual-Band N Entertainment Bridge. The bridge can connect any wired, Ethernet device to your wireless network. The bridge is based on dual-band Wireless-N, so it is compatible with any Wireless-N, -G, -A, or -B router or access point. [. . . ] The default is 0, which disables the timeout. Aggregation Window Size  This option defines the maximum number of packets transmitted without getting ACKs. Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes. wireless > Advanced Wireless Settings Configure the bridge’s advanced wireless functions. These settings should only be adjusted by an expert administrator as incorrect settings can reduce wireless performance. Voice Use Aggregation  This option defines whether or not the Media Access Control (MAC) layer will set up an Add Block Acknowledgement (ADDBA) session. Accept Aggregation  This option defines whether or not the MAC layer will accept an ADDBA request. Number of Packets in Aggregation  This option defines the maximum number of packets (sub-frames) in the aggregate. Aggregation Size  This option defines the maximum size of the aggregate (in bytes). Timeout Internal  This option defines the timeout period in which the aggregate should be closed with a “closing condition” before it is closed by the timer. Size of Packet in Aggregation  This option defines the minimum size (in bytes) of packets to be accumulated in the aggregate. Note The settings on the Advanced Wireless Settings screen are designed for advanced users only. advanced Wireless Use LDPC  Low-Density Parity-Check Code (LDPC) enables or disables error correction to reduce the probability of data loss in noisy channels. The Rate Adaptation algorithm automatically disabled LDPC coding when working at high PHY rates (higher than 162). To use the LDCP advanced error correction scheme, keep the default, Yes. 11b rates, the bridge informs the wireless network that OFDM packets are going to be transferred and protects the packets in the wireless network. The RTS/CTS and CTS2Self packets create overhead, which may result in lower throughputs. The RTS/CTS option provides better coverage but lower throughputs when compared to CTS2Self, because the RTS/CTS option includes acknowledgement from the receiving device. To use the RTS/CTS option, keep the default, RTS/ CTS. The None option may cause collisions between OFDM and CCK packets. 11n Protection Type  This option configures protection from non-High Throughput (HT) devices within the wireless network. In case the wireless router (or access point) detects an association of a non-HT legacy device, it will signal all the HT devices to use RTS/CTS or CTS2Self mechanisms before each data transmission. [. . . ] Hvis du valgte Wide - 40MHz Channel (Bred - 40 MHz-kanal) som ruterinnstilling for radiobånd eller kanalbredde, vil standardkanalen være en sekundær kanal for Wireless-N. Security (Sikkerhet)  Sikkerhetsmetoden for det trådløse nettverket vises. 11n (40 MHz): -69 dBm (vanlig) ved MCS15 1 WEP, Wi-Fi Protected Access™ (WPA), Wi-Fi Protected Access™ 2 (WPA2) Opptil 128-biters kryptering Omgivelser Mål Vekt Sertifisering Strøm Driftstemperatur Oppbevaringstemperatur Luftfuktighet for drift Luftfuktighet for oppbevaring 177 cm x 128 cm x 68 cm 295 g FCC, UL/cUL, ICES-003, RSS210, CE, Wi-Fi (IEEE 802 11a/b/g/draft n), WPA2™, Wi-Fi Protected Setup, WMM® 12 V, 1 A 0 til 40 ºC -20 til 60 ºC 10–85 % ikke-kondenserende 5–90 % ikke-kondenserende Spesifikasjonene kan endres uten varsel. 18 Linksys WES610N/WET610N Spesifikasjoner Omgivelser Mål Vekt Sertifisering Strøm Driftstemperatur Oppbevaringstemperatur Luftfuktighet for drift Luftfuktighet for oppbevaring 145 cm x 106 cm x 52 cm 159 g FCC, UL/cUL, ICES-003, RSS210, CE, Wi-Fi (IEEE 802 11a/b/g/draft n), WPA2™, Wi-Fi Protected Setup, WMM® 12 V, 1 A 0 til 40 ºC -20 til 60 ºC 10–85 % ikke-kondenserende 5–90 % ikke-kondenserende WET610N Modell WET610N Standarder IEEE 802. [. . . ]