User manual LOGITECH HARMONY 885 VERSION 1.1

[. . . ] Harmony 885 User Manual version1. 1 Harmony 885 User Manual Table of Contents INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 GETTING TO KNOW YOUR HARMONY REMOTE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 BEGIN THE SETUP PROCESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 USING YOUR HARMONY REMOTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 1. 1 page 3 Harmony 885 User Manual Using Your Harmony Remote This section provides you with information that will help you use your remote. Using the Glow Button Press the Glow button to light up or turn off the display backlight. To determine the length of time the backlight stays on. Note: Shaking or tilting the Harmony remote will not light up the display backlight. Users must press the Glow button to light up the display backlight. The remote will go into Deep Sleep mode when the remote detects no motion for two hours. The remote will begin motion sensing in Deep Sleep mode, and any motion or movement in front of the remote will trigger the glow. Use the Harmony Remote Software to enable/disable these features. Recharging the Battery Place your remote in the base station to charge. While the remote's battery is charging: · The display and its backlight, and the keypad backlight remain on. Note: Press the GLOW button to turn the backlight off. · The battery level icon in the status bar flashes when the battery is still charging or will display a full battery level when charging is complete. When the battery is low, the display will flash a message to remind you to charge the battery. Using the Tilt Sensor When you pick up the remote slightly tilted, the display will automatically turn on and the keypad light up. Note: Whenever you pick up the remote from the base station, or replace it in the station, you will hear a beep. Use the Harmony Remote Software to enable/disable this feature. Selecting an Activity View the Activities you have added by pressing the Activities button. The display will then list the Activities you have added. Press the corresponding display button next to the Activity you want to start. As a default, when you select an Activity, you will see a message on the remote's display reminding you to keep the remote pointed at your entertainment system while the Activity starts. This helps ensure that all infrared (IR) signals are properly sent. Use the Harmony Remote Software to turn on/off the "Starting Activity" message. 1. 1 page 4 Harmony 885 User Manual Using the Teletext Buttons When you press any of the Teletext button the homepage for Teletext will appear on the television (it may take a few seconds for the page to appear). The Teletext page will completely replace the televisionpicture, but sound will still be available. Each Teletext page has a unique 3-digit page number; all pages can be accessed by entering the 3-digit page number using the numbered channel buttons on your Harmony remote. While Teletext is the default settings for these buttons in the Watch TV Activity, you can customize these buttons to send different commands in other Activities. See Changing the Behavior of Buttons Within an Activity. Viewing the Status and Navigation Bars The status bar provides users with important information such as: · · · · · · A: Date and time B: Indicator if the USB is attached C: Indicator when infrared (IR) commands are being sent to your devices D: Battery indicator (battery's power) E: Activity you are in (if applicable) The navigation bar displays information such as: F: The number of screens available in a menu, and the screen currently displayed Displaying Help on Your Harmony Remote From time to time when you select an Activity, the Activity may not work. While the Help button helps you solve device problems within an Activity, the Remote Assistant teaches you how to use your Harmony remote. [. . . ] The Harmony remote uploads it via the USB cable (and your computer's internet connection) to the Harmony remote database. The Harmony Remote Software will try to find a matching pattern for the infrared signal. If no pattern is found, the signal will be stored as-is in its original format. If a pattern is found, the Harmony Remote Software converts the signal into a format for convenient storage. [. . . ]