User manual LUMAGEN RADIANCE XD

[. . . ] RadianceXD/XE® Video Processor Owner's Manual Rev_112809 LEGAL NOTICES: TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT SHALL LUMAGEN, ITS SUPPLIERS, OR ITS DEALERS, BE HELD LIABLE FOR INJURY TO PERSONS OR PROPERTY, ANY LOST REVENUE, LOST PROFIT, SPECIAL, INCIDENTAL, INDIRECT, CONSEQUENCIAL, OR PUNITIVE DAMAGES, IMPAIRMENT OF OR DAMAGE TO OTHER GOODS, HOWEVER CAUSED REGARDLESS OF THE THEORY OF LIABILITY, RESULTING FROM THE USE OF, OR INABILITY TO USE, THIS PRODUCT, EVEN IF LUMAGEN, ITS SUPPLIERS, OR ITS DEALERS, HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. LUMAGEN SHALL NOT BE LIABLE FOR OMISSIONS OR ERRORS IN ITS DOCUMENTATION OR SOFTWARE. LUMAGEN RESERVES THE RIGHT TO MAKE CHANGES TO ITS PRODUCTS AND DOCUMENTATION WITHOUT NOTICE. Unless you are experienced in the installation and set-up of high-performance video electronics, we suggest you hire a professional home-theater specialist to do installation and configuration of this product. We recommend that you choose a professional who has been certified by the Imaging Science FoundationTM (ISF). [. . . ] Set it to the default setting of 'Off' if your display will not take a slightly altered rate. The command is: MENU Output Configs [Config] Timing Rate Match (On, Off) Screen Aspect Ratio Select the screen aspect ratio. The screen aspect ratio range is 1. 33 (4:3) to 2. 50 and is entered in units of hundredths (e. g. If you have a normal fixed aspect display, select the (default setting) "Single output aspect". If you have a movable anamorphic lens, select "Output aspect per input aspect". There is a special case when you use NLS input aspect with "Output aspect per input aspect". When the input aspect is 4. 3+NLS the output aspect assigned to the 16:9 entry is used. When the input aspect is LBOX+NLS, 16:9+NLS, or 1. 85+NLS the output aspect assigned to the 2. 35 entry is used. The command is: MENU 0 6 (Single output aspect, Output aspect per input aspect) OK xxx OK or MENU Output Configs [Config] Aspect Ratio (Single output aspect, Output aspect per input aspect) Ok xxx Ok Graybar Intensity NOTE: Consult a home theater specialist for assistance setting the graybar intensity. Some degree of burn-in will occur on any susceptible display, but this command can help minimize it by allowing the intensity of the graybars to be adjusted. The command is: MENU Output Configs [Config] Other Graybar (Sides, Top/bottom) Output Type You can specify the black pedestal as "RGB-PC level" (0 IRE) or "RGB-Video level" (7. 5 IRE). "YCbCr 422" and "YCbCr 444" are video level (7. 5 IRE). For the HDMI output, setting the level as video allows blacker-than-black and whiter-than-white. Setting the level as PC allows full-range black to white. The command is: MENU Output Configs [Config] HDMI Format Type (VCbCr422, VCbCr444. RGB-PC level, RGB-Video level) Dither Some fixed pixel displays show contouring on images that have gradients because the actual resolution of the each pixel is less than 8-bits. The dither control can be used to enhance the resolution of the display and reduce contouring. Dither position sets the bit size of the pixel for dithering. Orientation controls the frame-to-frame randomization and can be fixed of dynamic. Masking can be turned on to clear the lowest bits after the dither position. The command is: MENU Output Configs [Config] HDMI Format Dither Mask and Shrink The "mask" command allows you to "blank" the edges of the video image on the output without changing its position or size. The gray level of the mask is adjustable from black to white in sixteen steps. [. . . ] ASCII extended characters set solid block for use as a volume bar. Set zoom factor to M-- Where M can be 0-2 (or 0-7 if zoom is set for 5% steps) Set output aspect ratio to MMM for all input aspects--. Where the valid range is 110-250 which corresponds to 1. 10 to 2. 50. Set output shrink parameters-- Where MMM=top, NNN=left, OOO=bottom, PPP=right edge. [. . . ]