User manual LYNX C DA 3000

[. . . ] LYNX Technik shall not be obligated to furnish service under this warranty a) to repair damage resulting from attempts by personnel other than LYNX Technik representatives to install, repair or service the product; b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any damage or malfunction caused by the use of non LYNX Technik supplies; or d) to service a product which has been modified or integrated with other products when the effect of such modification or integration increases the time or difficulty servicing the product. THIS WARRANTY IS GIVEN BY LYNX TECHNIK WITH RESPECT TO THIS PRODUCT IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED. LYNX TECHNIK AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. LYNX TECHNIK`S RESPONISIBILITY TO REPAIR AND REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY. [. . . ] Module configuration is set via a small dip-switch located behind an access hole in the bottom of the module. If the module is being used in a stand alone application then the optional power supply (R PS 3001 E, R PS 3001 U, R PS 3001-3 or R PS 3004) is required to power the module (not shown) Page 9 Reference Manual C DA 3000 Version 2. 0 Figure 2 ­ Module Layout Page 10 Reference Manual C DA 3000 Version 2. 0 Connections Video Connections The C DA 3000 MiniModule is configured with standard 75 Ohm BNC connectors. We recommend the use of high quality video cable suitable for digital video connections to reduce the risk of interference or errors due to excessive cable attenuation. Due to the compact design of the module it will be necessary to use a connection tool to secure the BNC video connectors to the module. Page 11 Reference Manual C DA 3000 Version 2. 0 Power Connections If using the module in a stand-alone application use the separate R PS 3001 E (for Europe), R PS 3001 U (USA) power brick option, the R PS 3001-3 desk power supply or the R PS 3004 desk power supply for 4 MiniModules. DC Power Connector The MiniModule has a captive power lead fitted to the module, with a male 5 pin locking bayonet connector. This connection provides DC power and also data connectivity to the module. Connector wiring is shown below. Data Connection Power Connection i2C-SDA (data) i2C-SCL (clock) 4 5 3 2 1 GND + 5V Male Connector (view looking into connector from front) ! Page 12 Caution Only use the optional LYNX R PS power modules. Ensure the 5-pin power connector is locked securely in place. Reference Manual C DA 3000 Version 2. 0 Installation Mechanical Stand Alone Operation The C DA 3000 MiniModule can be used in a stand alone application. There are two options for the use of the module in this way. a) Using the R FR 3005 Rack Frame 1 option. This allows up to any 10 of the MiniModules to be secured onto a rack frame assembly for 19 inch rack mounting. This keeps the modules secured, organized and out of the way. The rack frames are designed for installation in the back of 19-inch racks where there is normally plenty of available space. Ideal for mobile truck installations and facility expansions where space is at a premium. Page 14 Reference Manual C DA 3000 Version 2. 0 Electrical Installation. Stand Alone Operation The MiniModule requires the R PS 3001 power brick option for stand-alone operation. Four versions are available: R PS 3001 E for European markets, R PS 3001 U for the US markets, the R PS 3003-3 desk power supply or the R PS 3004 desk power supply for four MiniModules. Please ensure you have the correct power option for your region. The connection to the module is made with a small 5pin connector, which has a twist bayonet securing system. Please make sure the connection is solid and locked in place. A strain relief is included within the module to prevent excessive strain on the connection. Signal connections should be made with care, please ensure connections are correct and compatible equipment is feeding / receiving the signals from the module or damage can result. !Only use the optional LYNX R PS power modules. Ensure the 5-pin power connector is locked securely in place. Care needs to be taken when using the module in this way, if it is not physically secured. [. . . ] Can be combined with R FR 3005 1. 5m cable extension to connect one MiniModule to R FR 3010 2. 5m cable extension to connect one MiniModule to R FR 3010 Redundant power supply for the R FR 3010 card cage Rack controller for the R FR 3010 rack frame Master controllerwith TCP/IP Interface for the R FR 3010 rack frame Rack Bus Extension for R FR 3010 rack frame. In combination with R CT 5020 Service Adapter for remote configuration of one MiniModule via PC or Palm R PS 3001 U R PS 3001-3 R PS 3004 R FR 3004 R FR 3005 R FR 3010 R PS C15 R PS C25 R PS 5010 R CT 5020 R CT 5030 R CT 5010 R CT 3000 Page 22 Reference Manual C DA 3000 Version 2. 0 Parts List Due to the very dense design and high level of integration there are no user serviceable electronic assemblies within the C DA 3000 module. C DA 3000 Mini Module (complete) Description Video DA converter Model Number C DA 3000 Part Number 6. 155. 001. 280 Service If you are experiencing problems, or have questions concerning your C DA 3000 MiniModule please contact your local distributor for assistance. We offer a fixed cost service exchange program for defective Series 3000 MiniModules out of Warranty. [. . . ]