User manual MACKIE M2600

[. . . ] FULL SYMMETRY DUAL DIFFERENTIAL HIGH CURRENT DESIGN PROFESSIONAL POWER AMPLIFIER CH OL 3v 21 2v ­6 ­9 29 31 ­20 11 17 19 27 23 25 ­3 GAIN/dB GAIN/dB CH CH CH 3v OL 1 INTERNAL STATUS PROTECT SHORT 2 1 2 21 23 25 ­3 2v 19 27 ­6 17 29 ­9 11 31 ­20 0 0 33 1v 0 0 33 1v SENSITIVITY SIG SIG SENSITIVITY 1. 23v (+4dBu) 1. 23v (+4dBu) TEMP STATUS CH 1& 2 COLD HOT POWER TM CAUTION TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. REFER SERVICING TO QUALIFIED PERSONNEL. WARNING: SERIAL NUMBER MANUFACTURING DATE 1 CHANNEL INPUT LOW CUT FILTER TYPICAL 35 Hz CHANNEL CROSSOVER AMP MODE 60Hz STAGE MONITOR 100 Hz OFF 170 Hz 2 CROSSOVER LOW CUT FILTER 90Hz INPUT RISK OF ELECTRIC SHOCK DO NOT OPEN AVIS: RISQUE DE CHOC ELECTRIQUE -- NE PAS OUVRIR BALANCED OR UNBALANCED CONCEIVED AND DESIGNED BY MACKIE DESIGNS INC · WOODINVILLE WA · 98072 · USA · PATENTS PENDING · COPYRIGHT ©1998 · THE FOLLOWING ARE REGISTERED TRADEMARKS OF MACKIE DESIGN INC. : "MACKIE", "FR SERIES", AND THE "RUNNING MAN" FIGURE · 120Hz STEREO TYPICAL MONO BRIDGED 60Hz 90Hz 120Hz TYPICAL 35 Hz BALANCED OR UNBALANCED R R CH MONO BRIDGE HIGH-CURRENT POWER AMPLIFIER 1 + + + ­ CH SUB WOOFE SUB WOOFE 120 VAC 60 Hz 2000 WATTS 1300 WATTS / CH 2 OHM LOAD MIN. 2600 WATTS 4 OHM LOAD MIN. STAGE MONITOR 100 Hz 2 MONO BRIDGE CH's SUMMED OFF 170 Hz OUTPUT APPLICATION M·2600 OWNER'S MANUAL LOW OUT FULL RANGE (SUB WOOFER) ­ ­ PIN 1+ CH2+ PIN 1­ CH2­ PIN 2+ & 2 ­ NOT USED PIN 1+ BRIDGE+ PIN 1­ BRIDGE ­ PIN 2+ & 2 ­ NOT USED THRU THRU IN SWITCHED OUTPUT LOW HIGH OUT OUT OFF ON TYPICAL HIGH LOW OUT OUT THRU THRU PIN 1+ CH1+ PIN 1­ CH1­ PIN 2+ & 2 ­ NOT USED IN (CH1 & CH2) SPEAKER OUTPUTS CAUTION LETHAL VOLTAGES MAY APPEAR AT OUTPUT TERMINALS. CLASS 1 WIRING IS REQUIRED LIMITER SWITCHED OUTPUT CAUTION AVIS 8. [. . . ] If your console has an output impedance of 100 ohms, then you can daisy-chain up to twenty M·2600 amplifiers, which presents a load of 1200 ohms to the console (input impedance of 24 kohms divided by 20 amplifiers = 1200 ohms). The THRU jacks can also be used to relay the signal on to other devices such as a DAT or cassette recorder, enabling you to record exactly what the audience is hearing. In the THRU position of switch , the THRU jacks are wired straight from the XLR and TRS INPUTs -- so the signal coming out of the THRU jacks is exactly the same as the signal going into the amplifier. You can also use the 1/4" TRS INPUT jacks as THRU jacks, (not affected by switch or by the LOW CUT FILTER ). Connect the 1/4" TRS INPUT jacks on the first amplifier to the TRS 1/4" INPUT jacks on the second amplifier using 3-conductor shielded cables with TRS plugs on both ends. Warning: If you use a regular guitar cord with 2-conductor TS plugs, you'll unbalance the signal at the XLR input by grounding the low side (­) of the signal (pin 3). 2 COLD SHIELD 3 1 1 COLD 3 HOT 2 SHIELD COLD 1 3 2 HOT Balanced XLR Connectors: Apollo/Soyuz Rendezvous The M·2600 amp expects to see a nominal signal level anywhere between the ­10 dBV "semipro" and +4 dBu "pro" standards, meaning almost any line-level mixer or other device can be plugged into the amp's INPUTs. Use controls to adjust the gain of the the GAIN amplifier to match the signal level you're using. THRU and THRU SWITCH Someday you'll do a show at NudeStock and realize that one M·2600 amplifier is just not going to do the job -- you'll need a six-foothigh rack full of 'em to hide behind. It has three modes of operation, depending on the setting of the THRU switch : · THRU, a straight copy of what's going into the amplifier, nothing added or taken away from your big finish on spoons. · LOW OUT, the lower frequencies only, below the frequency set by the CROSSOVER switch . · HIGH OUT, the higher frequencies only, above the frequency set by the CROSSOVER switch . Note that the LOW OUT and HIGH OUT are also affected by the setting of the LOW CUT FILTER . LOW CUT FILTER Every woofer has frequency response specifications. It's usually expressed in Hertz (or cycles per second), like "40Hz­300Hz. " The "40Hz" refers to the low-frequency point (usually, but not always) where the speaker's output drops by 3 dB, and will "roll off" completely as the frequency goes down. There is no point in sending a woofer any frequencies it can't reproduce -- you can't hear it, and worse yet, it's a waste of amplifier power that can be better used reproducing frequencies you can hear. 24 5dB CROSSOVER SWITCH This three-way switch allows you to set the crossover point of the internal CROSSOVER to either 60Hz, 90Hz or 120Hz. This affects two things: · The THRU output , if the THRU switch is set to LOW OUT or HIGH OUT. · The SPEAKER OUTPUTS , if the OUTPUT APPLICATION switch is set to LOW OUT. The amplifier then plays the frequency range below the crossover point. affects Note: The LOW CUT FILTER and the SPEAKER both the THRU outputs in the cases above. OUTPUTS Level, dB 0dB ­5dB ­10dB ­15dB 1Hz 10Hz 100Hz 1kHz 10kHz 20k Frequency, Hz L C Fil Low Cut Filter Frequency Response In order to match the output bandwidth with your particular speaker system, the M·2600 amplifier has a tunable LOW CUT FILTER. The frequencies are marked along the knob's travel : · Fully counterclockwise, the frequency is below 10Hz, effectively bypassing the filter. · Center detent is 35Hz and labeled TYPICAL, since precious few woofers actually go below that. · 3/4 of the way up is labeled STAGE MONITOR, 100Hz, perfect for stage monitors (they seldom reproduce below 100Hz; besides, it prevents low-frequency "leakage" into the house). · Fully clockwise is labeled 170Hz. [. . . ] But rather than get too deep into this, let's just summarize the basics, as they apply to you and your M·2600 power amplifier: · As a load gets "heavier, " its impedance in ohms decreases. · The lower the impedance (ohms), the higher the power: The M·2600 has 1300 watts (per side) with a 2-ohm load, 850 watts with 4 ohms, and 500 watts with 8 ohms. · Do not connect a load of under 2 ohms (in STEREO and MONO mode) or 4 ohms (in BRIDGED mode). · Never plug amplifier outputs into anything except speakers (unless you have an outboard box designed to accept speaker levels). [. . . ]