User manual MACKIE PA281 DATASHEET

[. . . ] The low-frequency transducers are two 8inch carbon fiber woofers suitable for difficult climatic environments. The system includes a high-level crossover network that features markedly lower (than conventional) induction values in series with the woofer. We call this innovation LICC (Low Impedance Compensated Crossover). [. . . ] Listed sound pressure represents an average from 300 Hz to 3 kHz. 2 O Fo F66 PAAG E SE S PG PA281 Compact Two-Way Speaker System PA281 Vertical Polars 120° 90° 60° 120° 90° 60° 150° 30° 150° 30° 200 Hz 250 Hz 180° ­36 ­12 500 Hz 630 Hz 180° ­36 ­12 0° 315 Hz 400 Hz 0° 800 Hz 1 kHz 210° 330° 210° 330° 240° 270° 300° 240° 270° 300° 90° 120° 60° 120° 90° 60° 150° 30° 150° 30° 1. 25 kHz 1. 6 kHz 180° ­36 ­12 3. 15 kHz 4 kHz 180° ­36 ­12 0° 2 kHz 2. 5 kHz 0° 5 kHz 6. 3 kHz 210° 330° 210° 330° 240° 270° 300° 240° 270° 300° PA281 Vertical Off-Axis Frequency Response (UP) 90° 10 Attenuation (dB) 120° 60° 0 0 deg ­10 deg ­10 ­20 deg ­30 deg 150° 30° ­20 ­40 deg 100 1000 10000 20000 8 kHz 10 kHz 180° ­36 ­12 ­30 20 0° Frequency (Hz) 12. 5 kHz 16 kHz 10 PA281 Vertical Off-Axis Frequency Response (DOWN) 0 deg ­10 deg ­10 Attenuation (dB) 210° 330° 0 ­20 deg ­30 deg 240° 270° 300° ­20 ­40 deg 100 1000 10000 20000 ­30 20 Frequency (Hz) 3 O Fo F66 PAAG E SE S PG PA281 Compact Two-Way Speaker System PA281 Horizontal Polars 0° 330° ­12 0° 30° 330° ­12 30° 300° ­36 60° 300° ­36 60° 200 Hz 250 Hz 270° 90° 315 Hz 400 Hz 270° 90° 500 Hz 630 Hz 800 Hz 1 kHz 240° 120° 240° 120° 210° 180° 150° 210° 180° 150° 0° 330° ­12 0° 30° 330° ­12 30° 300° ­36 60° 300° ­36 60° 1. 25 kHz 1. 6 kHz 270° 90° 2 kHz 2. 5 kHz 270° 90° 3. 15 kHz 4 kHz 5 kHz 6. 3 kHz 240° 120° 240° 120° 210° 180° 150° 210° 180° 150° 0° 330° ­12 PA281 Horizontal Off-Axis Frequency Response 10 30° Attenuation (dB) 0 0 deg 10 deg 300° ­36 60° ­10 20 deg 30 deg 8 kHz 10 kHz 270° 90° 12. 5 kHz 16 kHz ­20 40 deg 100 1000 10000 20000 ­30 20 Frequency (Hz) 240° 120° 210° 180° 150° 4 O Fo F66 PAAG E SE S PG PA281 Compact Two-Way Speaker System Frequency Response is measured on-axis at a distance referenced back to 1m at 1-watt drive. Shown as a half space (2) environment. 100 316 80 70 10 60 20 100 1000 10000 20000 Frequency (Hz) Beamwidth vs. Frequency 360 20 Directivity Index 100 ­6 dB Beamwidth (degrees) Directivity Index (DI), dB 300 240 180 120 60 0 20 Impedance (ohms) 90 100 SPL, 1W/1m (dB) 10 10 Vert BW Horz BW 100 1000 10000 20000 Frequency (Hz) 0 20 100 1000 10000 1 20000 Frequency (Hz) 30. 31" (770mm) 11. 08" (281. 5mm) 5. 31" (135mm) 13° 3. 15" (80mm) 12. 87" (328mm) 15° 4. 39" (112mm) 8. 23" (209. 1mm) 12. 87" (328mm) TOP SIDE 2. 76" (70mm) 12. 66" (321. 5mm) 21. 5" (546mm) 30. 31" (770mm) 5. 0" (127mm) 12. 66" (321. 5mm) 1. 38" (35mm) 6. 3" (160mm) 12. 0" (305mm) 4. 33" (110mm) FRONT REAR 5 O FoF66 PAGESE S PAG Directivity Factor (Q) SPEAKER PA281 Compact Two-Way Speaker System Architects' and Engineers' Specifications The two-way loudspeaker system shall be self-contained and consist of the following components: (1) two 8-inch, lowfrequency drivers; (2) a high-frequency section consisting of a constant-directivity horn and compression driver; (3) a twoway crossover network; (4) a vented enclosure. The two low-frequency transducers shall be cone type loudspeakers having cone diameters of at least 8 inches/203 mm. They shall have voice coils of at least 3 inches/76 mm in diameter and carbon fiber diaphragms. Together they shall present a nominal impedance load of 4 ohms. Sensitivity shall be at least 92 dB when measured at 1 m with an input of 1 watt. The high-frequency section shall have a compression driver with a titanium diaphragm of at least 1. 75 inches/44 mm in diameter. It shall present a constant-impedance load of 8 ohms. It shall be connected to a constant-directivity horn having a throat diameter of at least 1 inch/25 mm and a nominal coverage pattern of 100° horizontal by 85° vertical. Sensitivity shall be at least 107 dB when measured at 1 m with an input of 1 watt. The system shall be crossed over by an internal, highlevel, passive network having a response of 12 dB/octave. The nominal crossover frequency shall be 2. 1 kHz. The lowpass section of the network shall have minimum inductance in series with the low-frequency drivers. The high-pass section of the network shall be equalized to optimize the performance of the constant-directivity horn. A dynamic high-frequency protection circuit based on a low-value, lowmass filament resistor shall limit the current available to the compression driver. [. . . ] New material, production methods, and design refinements are introduced into existing products without notice as a routine expression of that philosophy. For this reason, any current Mackie product may differ in some respect from its published description, but will always equal or exceed the original design specifications unless otherwise stated. Mackie and the "Running Man" figure are registered trademarks of Mackie Designs Inc. [. . . ]