User manual MACKIE REMOTE48

[. . . ] REMOTE 48 USER'S GUIDE PROFESSIONAL REMOTE CONTROL FOR THE HDR24/96 HARD DISK RECORDER REMOTE 48 CAUTION AVIS RISK OF ELECTRIC SHOCK DO NOT OPEN RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL 11. Servicing -- Do not attempt to service the Remote 48. All servicing should be referred to the Mackie Service Depart ment. Lightning -- Unplug the Remote 48 during lightning storms or when unused for long periods of time. [. . . ] When AUTO INPUT is on, armed tracks monitor their tape inputs in stop, fast forward, rewind, and record. In play, they monitor the playback of previously recorded audio; this mode is used for overdubbing. Unarmed tracks always monitor the playback of previously recorded audio. ALL INPUT AUTO INPUT Record Safe REC SAFE disarms all tracks and disables all recording controls. When enabled, Record Safe prevents you from arming tracks and entering record. Lock Out LOCK OUT disables user input from all software and hardware controls while allowing the HDR24/96 to otherwise operate normally. To engage or disengage lock out on the Remote 48, hold down the LOCK OUT button for 1 second. The Lock Out LED blinks when enabled and is off when disabled. Use Lock Out to prevent someone from disturbing the HDR24/96 during critical operations, such as when recording live performances. REC SAFE LOCK OUT 10 Record/Monitor Controls System Controls The System Controls that are unique to the Remote 48 are described below. For more detail on System Controls that are common to both the HDR24/96 and Remote 48, see the HDR24/96 Technical Reference Manual or QuickStart Guide. DECK 2 EDIT DEC INC T- CODE CHASE VARI ALT CONTROL User's Guide Deck 2 The DECK 2 button toggles Remote 48 control of the LCD display, Rates display, and System Control buttons between the Master and Slave HDR24/96. The Remote 48 controls the Master HDR24/96 when the Deck 2 LED is off, and the Slave HDR24/96 when the Deck 2 LED is blinking. DECK 2 Edit The Edit button is not presently implemented and is reserved for a future software upgrade. EDIT Vari Varispeed is not presently implemented in the HDR24/96. This button is reserved for a future software upgrade. VARI ALT The ALT button modifies the functionality of another button. Specific uses of the ALT button are documented within the function(s) it modifies. ALT Control The CONTROL button modifies the functionality of another button. Specific uses of the CONTROL button are documented within the function(s) it modifies. CONTROL Remote 48 User's Guide 11 Remote 48 Displays Tape Time The TAPE TIME display always shows the current position of the HDR24/96 "play head" (Current Time). It is the same as the Current Time displays on the HDR24/96 front panel and GUI. Tape Time (Current Time) Locate Time TIME The LOCATE TIME displays the time that the Transport will locate LOCATE to when the LOCATE button is TIME pressed, and corresponds to the LOCATE TIME display in the GUI Locate Time Cues List. Locate Time also acts as a scratchpad or working display from which you can preview and recall stored time values, manually enter and store specific times to these values, or display the result of time code addition/subtraction operations. TAPE Vari The VARI (Varispeed) display shows the transport speed whenever SHUTTLE or JOG is enabled. Depending on the speed, the Varispeed display shows quantized values of 0. 0, 0. 03, 0. 06, 0. 12, 0. 25, 0. 5, 1. 0, and 2. 0 in Shuttle, and contiguous values between 0. 00 and 1. 00 in Jog. The blinking Rewind LED indicates reverse motion (negative speeds). VARI Cue The CUE number display shows the Cue number that was last entered, stored, or recalled. It also shows the names of other stored values (Pre for Pre-roll, LOP for loop length, PCH for Auto Punch, L1 ­ L4 for Loc 1 through Loc 4, and PLA for the last play start position) during a Recall operation. CUE Rates 44. 1k, 48k, 96k (Sample Rate) The Sample Rate LEDs indicate the system sample rate setting. The 44. 1k and 96k LEDS light simultaneously to indicate a sample rate setting of 88. 2kHz. RATES 44. 1k VARI ERROR 48k 96k Vari (Varispeed) When the sample clock is set to either Word Clock or Video, the VARI LED lights when the actual sample rate differs from the sample rate setting by more than ± 0. 2%. 16 BIT 24 BIT TC CLOCK 16 Bit, 24 Bit (Bit Depth) The 16 BIT and 24 BIT LEDs reflect the system bit depth setting. Error The ERROR LED blinks when there is a system error that requires user attention. Selecting Cancel from the LCD display clears the error message. 12 Locator/Time Displays User's Guide TC (Time Code) The TC LED represents the status of the HDR24/96 with respect to received time code. When T-CODE CHASE is enabled, the TC LED blinks when either no time code is present or time code is unreadable, and glows when the HDR24/96 is locked to time code. The TC LED is off when T-CODE CHASE is disabled. Clock The CLOCK LED glows when the system is locked to the selected sample clock source, and blinks when the sample clock source is not present or out of range. [. . . ] · [RECALL This is a shortcut to save you from having to type the Cue number. · [RECALL +NEXT or ­PREV (one or more times or hold to scroll), or Wheel ENTER] Recalls a Cue from the Cue List. Rotating the wheel or pressing +NEXT or ­PREV allows you to scroll through the Cue List in chronological order until you find the desired Cue. Using RECALL, you · [RECALL can also locate to any stored value without overwriting the current Locate Time value; the previous value of Locate Time is restored after the operation is completed. [. . . ]