User manual MACROM M1A460

[. . . ] [. . . ] High Level Input Hig h Lev Inpu el t R+ RLL+ GND 2ch 4c h 2ch or 4ch selector Inp Lef t ut Low Level Input 2ch 4c h Rig ht M1A. 460 4 CHANNEL POWER AMPLIFIER R+ RLL+ GND High LeveInpu t l R+ RLL+ GND Left Inpu t fr ont Cont rol Righ t 1V Flat High / Fi lt REAR er Inpu tz 2ch 4ch 8V 150H 0, 2 30 Mode Illustration Guide For more informations <www. macrom. ch> Off On - EBC Rear Low Only or 600 Filt 150H FRONT Inp Lef t er z Flat / Co nt rol Inpu t Re ar Left Hig h Lev Inpu el t High LeveInpu t l Low 1V 30 600 8V Rig ut R+ RLL+ GND R+ RLL+ GND or Rig ht Input setting 8V 1V Front Filter setting Rear Filter setting Flat Response High Input Level Left R+ RLL+ GND Low Level Input 8V 0, 2 V 0, 2 V R+ RLL+ GND High Level Input Gain Control Adjust High pass filter control 20Hz 30Hz 600Hz 20kHz Input Control / Filter Flat Low 1V Right 8V 0, 2V 0 30 600 30 600 Input Rear Input - Mode - EBC ST Mono Input - Mode - EBC 2ch 4ch Off On Rear Low Only High Input Level R+ RLL+ GND Filter / Control Left Flat Low 150Hz 1V Rig 8V Off On Low Only 150Hz Con 1V tro 150 Hz 4V 600 Flat Hig l/ Fil t h 150 er 20Hz 30 20kHz 30 0, 2V 30 Hz 600 Con 1V 150 Hz 600 tro Flat Hig l/ Fil t h 150 er Con tro l/ Fil Fla ter 1V t Low 4V 0, 2 V 30 600 Con tro l/ Fil Flat ter 1V Low 4V 150 0, 2V 30 600 4V 0, 2V 30 Hz 30 30 600 600 Flat Response 150 Hz Hz 600 20Hz 30Hz 600Hz 20kHz Low pass filter control 20Hz 20kHz Technical Data IHF max power handling Configuration RMSPower 4 ohm Stereo load at 14, 4 V RMS Power 2 ohm Stereo load at 14, 4 V RMS Power 4 ohm Bridged load Frequency response (+0/-1 dB) Signal to noise ratio Input sensitivity Input impedance Crossover tipe Crossover frequency & filter slop (High-pass) Crossover frequency & filter slop (Low-pass) EBS External Bass Control Dimensions (w * h * d) mm 800 Watts "2 - 3 - 4" ch 70 x 4 watts 100 x 4 watts 200x 2 watts 10 - 50, 000 Hz > 100 dB 200 - 8, 000 mV 22. 000 ohm variable 30 to 600/12 Hz/dB 30 to 600/12 Hz/dB Yes 265 x 50 x 360 Output/Power connection M1A. 460 4 CHANNEL POWER AMPLIFIER EBC setting Illustration Guide For more informations <www. macrom. ch> + + L Spe ake Br i rO ut dge d - put + R - Inp ut -M ode Off On - EBC Low Onl y + + L Spe ake - r Bridg Out p ed + Spea L ut REA R + ker Bridg Outp ed + R - + Left REAR - ut + R 20A FRO N + Right T Fuse 20A 20A EBC setting +BAT T Pow er Te Rem rmin al -GN D ote Min load 2ohm + FRONT Right 2 30 600 + Left ont rol Flat High /F ilt er Inpu t- 150H z 2ch 4ch Mod Off On e- EBC Rear Low Only or Stereo Bridged Power connection + + L 150H z Fil ter /C ont rol Flat Low 1V 600 Inp ut Rea r Left 30 Hig h Lev Inpu el t 8V Rig R+ RLL+ GND Spe ake - Bridg rO utp u ed + Inp t R +BAT T Pow er T erm Rem ote ut -M od Off On ina l -GN D e- EBC Low Only - Min load 4ohm + + + L Bridged - Spe ake rO ut Bri dged - put REAR - + R + - + Bridged FRONT CAR CHASSIS Min CAR CHASSIS EBC connection Max [. . . ] [. . . ]