User manual MAGELLAN SP7000

[. . . ] MG5000 MG5050 SP5500 SP6000 SP7000 User Guide We hope this product performs to your complete satisfaction. Should you have any questions or comments, please visit www. paradox. com and send us your comments. User Settings For security reasons, write only the user's name and not his or her access code. 4-Digit Codes User # and Name 001: Master______________________ 002: Master 1____________________ 003: Master 2____________________ 004:____________________________ 005:____________________________ 006:____________________________ 007:____________________________ 008:____________________________ 009:____________________________ 010:____________________________ 011:____________________________ 012:____________________________ 013:____________________________ 014:____________________________ 015:____________________________ 016:____________________________ 017:____________________________ 018:____________________________ 019:____________________________ 020:____________________________ 021:____________________________ 022:____________________________ 023:____________________________ 024:____________________________ 025:____________________________ 026:____________________________ 027:____________________________ 028:____________________________ 029:____________________________ 030:____________________________ 031:____________________________ 032:____________________________ Partition 1 or 2 ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ ________ Byp Stay Force 6-Digit Codes Arm Only PGM Only Duress Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y Duress: Y N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N N Master Quick Menus User Step 1 2 3 4 5 6 Action [ ] + [MASTER CODE] Details The [ ] key will flash. [PARTITION MASTER CODE] may also be used. [. . . ] The [BYP] key will flash to indicate you are in the System Options menu. Press key [1] to set partition 1, or press key [2] to set partition 2. Press and hold [SLEEP] to temporarily disable the Auto-Arm Timer. No Movement Auto Arming The alarm system can be programmed to arm the system and/or send a report if no zone activity occurs for a pre-programmed amount of time. This is a particularly useful feature when supervising an individual with chronic health problems or a person who lives alone. The system will bypass any open zones. Disarming & Deactivating an Alarm To disarm an armed system or an alarm, press [OFF] and enter your [ACCESS CODE]. An entry point, like the front door, will be programmed with one of two Entry Delay Timers. When an entry point is opened, the keypad will beep until you disarm the system. Your alarm system will not generate an alarm until this timer elapses. Any user can disarm a partition they have been assigned to, except users assigned with the Arm Only Option or PGM Only Option. To disarm alarms generated by a Delayed Fire Zone, refer to Fire Alarms on page 12. (for a Stay or Sleep armed system, go to step 2) 1 2 3 Enter through a designated entry point (e. g. If you have access to both partitions (see Partitioning on page 6): Press the key corresponding to the desired partition ([1] or [2]). For both partitions, press the other key after the confirmation beep. How do I deactivate an alarm?· Press [OFF] + enter [ACCESS CODE]. Manual Bypass Programming Manual Bypass Programming allows you to program the alarm system to ignore (deactivate) specified zones the next time the system is armed. For example, you may wish to bypass certain zones when workers are renovating part of your home. Once the system is disarmed, the bypass entries are erased. When zones are bypassed, the [BYP] key will illuminate. Manual Bypass Programming can also be activated by using One-Touch Bypass Programming. If One-Touch Bypass Programming is enabled, press the [BYP] key for three seconds to enter Bypass Programming. To remove the Bypass feature from a zone, in step 3 enter the zone number again or press [CLEAR] to erase all current entries. Press [ENTER] after step 2 to bypass all open zones. Press [CLEAR] twice to exit without saving. Press [CLEAR] + [ENTER] to delete bypassed zones. [. . . ] or ___________ Silent [7] & [9] Fire or ___________ Silent Audible Audible Audible Off Off Off PGMs PGM 1 _____________________ PGM 2 _____________________ PGM 3 _____________________ PGM 4 _____________________ PGM 5 _____________________ PGM 6 _____________________ PGM 7 _____________________ PGM 8 _____________________ PGM 9 ____________________ PGM 10 ____________________ PGM 11 ____________________ PGM 12 ____________________ PGM 13 ____________________ PGM 14 ____________________ PGM 15 ____________________ PGM 16 ____________________ PGM Utility Keys [1] & [2]: _____________________________ [4] & [5]: _____________________________ [7] & [8]: _____________________________ [CLEAR] + [ENTER] = Smoke Reset [2] & [3]: _____________________________ [5] & [6]: _____________________________ [8] & [9]: _____________________________ System Timers Enter and exit your premises through the designated doors. = time to exit premises Exit Delay 2 (Partition 2): _______sec. = time to exit premises Entry Delay 1 = _______sec. = time to disarm before alarm; enter through zone #___________ Entry Delay 2 = _______sec. [. . . ]