User manual MAGNA-MATIC MAG-103 STAND ALL CHIPPER BLADE VICE

[. . . ] It provides five different mounting options, and is also included with the MAG-10300 Service Center Stand. MAG-10300 Service Center Stand The MAG-10300 is designed to bring the balancer and sharpener in to close proximity to create a productive work-station for blade service. MAG-3000 Chipper Blade Vice The MAG-3000 is designed to allow you to sharpen single-sided chipper/shredder blades in a Magna-Matic sharpener. MAG-3001 Large Chipper Blade Vice The MAG-3001 is designed to allow you to sharpen large double-sided chipper/ shredder blades in a Magna-Matic sharpener. 1 page Assembly Instructions for the MAG-10300 Service Center Stand Required Tools First gather all the require tools to assemble the stand. 1 2 3 4 5 6 (1) (2) (2) (1) (1) (1) 7/16 Combination Wrench 1/2 Combination Wrenches 9/16 Combination Wrenches 5/32 Hex Head Socket Wrench (Allen head wrench) Level Square Hardware Inventory This is a listing of all the parts and hardware that is included with your new MAG-10300 Service Center Stand. (04) (33) (02) (01) (02) (03) (33) (25) (01) (11) (04) 5/16" Bolt Button Head Socket (black) x 3/4" lg 5/16" Bolt Hex Head x 3/4" lg 5/16" Bolt Hex Head x 1-1/2" lg (MAG-9000 mounting) 3/8" Bolt Hex Head x 1-1/4" lg 3/8" Bolt Hex Head x 2" lg (MAG-8000 mounting) 5/16" Flat Washer 5/16" Lock Washer 5/16" Nut 3/8" Lock Washer 3/8" Nut Industrial Glides (leveling feet) Hardware for MAG-103 Balancer Stand (08) (08) (08) (08) (02) (02) (02) (02) 5/16" Bolt Hex Head x 3/4" lg 5/16" Flat Washer 5/16" Lock Washer 5/16" Nut 1/4" Fiber Washer 1/4" Bolt Socket Head x 3/4" lg 1/4" Lock Washer 1/4" Nut page 2 Parts Inventory Qty 01 01 02 01 01 05 01 02 01 Description Sharpener Table Top Column U-Brackets MAG-103 Table Top Support (opposite) MAG-103 Table Top Legs & MAG-103 Table Top Support Bottom Column Cover MAG-103 Ends MAG-103 Column Key # 1 2 3 4 5 6 7 8 9 Note: the diagram below does not represent quantity, it shows only the unique parts. [. . . ] BE SURE TO USE A SQUARE when attaching the supports to the center column. The same hole pattern is on each of the four sides of the column - this gives you the choice of where to place the balancer stand table of anyone of the 4 sides of the column. Step 5: Assemble the MAG-103 Balancer Stand table top to the supports from Step 4. You will require (4) 5/16" bolt hex head x 3/4" long - (4) 5/16" lock washers - (4) 5/16" nuts. 5 page Assembly Con't Step 6: Assemble the u-bracket to large sharpener table top; and then to the center column. You will require (2) 5/16" bolt hex head x 3/4" long - (2) 5/16" lock washers to connect the u-bracket to the sharpener table top. You will require (4) 5/16" bolt hex head x 3/4" long and (4) 5/16" lock washers to connect the u-bracket to the center column. The sharpener table top has 1 of 4 ways it can be placed on the stand, see the diagrams for the suggested orientation for each sharpener. Note: the sharpener table top has 2 slotted holes at one end - this is the "front" as shown in the diagrams page 6 Assembly Con't Step 7: MAG-103 Stand Assemble the MAG-103 balancer stand. You will require (8) 5/16" bolt hex head x 3/4" long - (8) 5/16" flat washers (8) 5/16" lock washers - (8) 5/16" hex nuts. Flat washers should be placed against the slots, as shown below. When positioning the MAG-103 arm - always be sure to check that the plate you mount the balancer to is VERTICAL. See page 9 to view suggested positions. 7 page Assembly Con't Step 8: Assemble the MAG-103 balancer stand to the MAG-10300. You will require (3) 5/16" bolt hex head x 3/4" long - (3) 5/16" flat washers (3) 5/16" lock washers - (3) 5/16" hex nuts; and for the middle pivot use (1) 3/8" bolt hex head x 3/4" long - (1) 3/8" lock washer - (1) 3/8" nut. The MAG-103 can be swiveled upon this table to suit your needs. Step 9: Assemble the MAG-1000 (or alternate) balancer to the MAG103. You will require (2) 1/4" bolt socket head x 3/4" long - (2) 1/4" fiber washers - (2) 1/4" lock washers - (2) 1/4" nuts. Step 10: Assemble the sharpener (MAG-8000 or MAG-9000) to the MAG-10300 Service Center Stand. DO NOT remove the rubber bumpers (feet) from the sharpeners. MAG-8000 requires (02) - 3/8" Bolt Hex Head x 2" lg (02) - 3/8" Nut MAG-9000 requires (02) - 5/16" Bolt Hex Head x 1-1/2" lg page 8 Assembled Images MAG-10300 Fully Assembled - for the MAG-8000 MAG-10300 Fully Assembled - for the MAG-9000 Table top side-view of possible positions Wall sideview of possible positions 9 page Chipper Blade Vices MAG-3000 This chipper blade vice is used to hold single sided chipper blades. Place a chipper blade in the jaws of the vice, use the slider bar to hold the chipper blade - and then turn the handle to increase tension onto the blade to keep it in place. [. . . ] Any tool or part proved to MAGNAMATIC's satisfaction to be defective during that period will be repaired or replaced at MAGNA-MATIC's option if returned prepaid. MAGNA-MATIC's sole obligation and your exclusive remedy under this warranty shall be limited to such repair or replacement. In no event shall MAGNA-MATIC be liable for any consequential or incidental damages. [. . . ]