User manual MAGNAVOX REM400

[. . . ] REM400 DSS Universal Remote Control User's Guide TABLE OF CONTENTS Introduction . 15 INTRODUCTION The DSS Universal Remote Control is the complete solution for all of your DSS remote control needs. Specifically designed to operate the features of your DSS satellite system, it can be programmed to operate a variety of components, up to six at a time, and is packed with easy-to-use features such as: · Fingertip navigation control of interactive DSS on-screen menus (see page 8). · Auto Scan code search to help program remote control for a variety of components, including older/discontinued models. [. . . ] Place your original remote control head to head (about 2" apart) from the DSS remote control. 2" DSS Directional Pad The DSS remote control allows you to control the on-screen menu just like you would with your original remote control. Pressing the MENU key allows you to access the onscreen menu of the component you have selected (e. g. While in the menu, you can use the directional pad* to navigate and change the settings of the menu. To exit out of the Menu mode, either press the MENU key again or the EXIT key (depending on how the original remote control functioned). *NOTE: If your component's On-Screen menu requires the use of the Volume and Channel keys to navigate and change the On-Screen menu settings, you will need to use the VOL+, VOL­, CH+, and CH ­ keys. 2. 3. 4. GUIDE Key The GUIDE key works just like the Guide key of your original remote control and allows you to access the On-Screen guide* of the component you have selected (e. g. While in the Guide mode, the directional pad will allow you to navigate Up, Down, Left and Right just like you would with your original remote control. To exit out of the Guide mode, either press the GUIDE key again or EXIT (depending on how the original remote control functioned) to return to normal operation. NOTE: *On-Screen guide is an interactive channel listings menu that is available on most DSS Satellite systems and is also used with advanced converters being offered by some cable systems. This feature is not applicable for all DSS or cable boxes. 5. On your original remote control, press and hold the key (i. e. , feature) to be learned until the red light on the DSS remote control blinks twice. If the red light does not blink twice, stop and repeat steps 1 through 5. To learn functions on the other L keys, repeat steps 3 through 6. To lock in new feature(s) on the DSS remote control, press and hold SET until the red light blinks twice. To test a new feature, press the component key that was learned once. Then press the L key where the component's feature was learned. 7. 8. SELECT Key The SELECT key lets you choose features displayed on the On-Screen menu and programs while in the Guide mode. If your original remote includes a Select key, then the DSS's SELECT key will operate in the same manner for the selected component. 9. 8 OPERATING YOUR REMOTE CONTROL (continued) Deleting Functions From The L Keys: 1. On the DSS remote control, press and hold SET until the red light blinks twice, then release SET. Press a Component key once (e. g. , TV, VCR, CBL, AUD, DSS, or CD). Repeat steps 4 and 5 for each component you want under master power on/off control. Press and hold SET until the red light blinks twice, then release SET. 2. 5. 6. 3. Press the component key once where the learned feature to be deleted is stored (e. g. , TV). [. . . ] Press component key to be reassigned once (e. g. , AUD). Reassigned key is now ready for programming. 1 2 3 4 Programming The FC Keys (See Page 9 For Further Instructions) x2 x2 or Press component key that controls channels once (e. g. , CBL). x2 Press SET Enter 9-9-5; Press FC1 or until Red Light the Red Light FC2 once. release SET. * NOTE: If over 100 channels, enter 0-7-1. Press SET until Red Light blinks twice; release SET. 1 2 3 4 5 Programming The L1~L3 Keys (See Page 8 For Further Instructions) x2 x2 Press SET until Red Light blinks twice; release SET. [. . . ]