User manual MAKITA 2703#2702X1

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MAKITA 2703#2702X1. We hope that this MAKITA 2703#2702X1 user guide will be useful to you.

Lastmanuals help download the user guide MAKITA 2703#2702X1.


Mode d'emploi MAKITA 2703#2702X1
Download
Manual abstract: user guide MAKITA 2703#2702X1

Detailed instructions for use are in the User's Guide.

[. . . ] WARNING: For your personal safety, READ and UNDERSTAND before using. Cutting capacities 45° Maximum dado capacity No load speed (RPM) Table size (W x L) Dimensions (L x W x H) Net weight 47 mm (1-3/4") 13 mm (1/2") 4, 600/min. Due to our continuing programme of research and development, the specifications herein are subject to change without notice. Note: Specifications may differ from country to country. [. . . ] Do not pull the switch lever hard without the key. CAUTION: Keep the flange surface clean of dirt or other adhering matter; it could cause blade slippage. Be sure that the blade is installed so that the teeth are aligned in the cutting (turning) direction. To secure the blade in place, hold the outer flange with the offset wrench, then tighten the hex nut clockwise with the wrench. CAUTION: Be sure to hold the hex nut carefully with the wrench. If your grip should slip, the wrench may come off the hex nut, and your hand could strike the sharp blade edges. If you tighten the hex bolts while grasping the offset wrench further than the striped portion, the hex bolts may be damaged and/or an injury to your hand may result. If the blade and spreader are not aligned properly, a dangerous pinching condition may result during operation. You could suffer serious personal injury while using the tool without a properly aligned spreader. NEVER make any adjustments while tool is running. Disconnect the tool before making any adjustments. There must be a clearance of about 4 - 5 mm (5/32" -13/ 64") between the spreader and the blade teeth. adjust the spreader accordingly and tighten the hex bolts (A) securely. Attach the table insert on the table, then check to see that the blade guard works smoothly before cutting. CAUTION: Before installing the blade guard, adjust the depth of cut to its maximum elevation. Insert the spreader between the blade guard mounting portion (stay) and the pressure plate. However, if they are not in a straight line, loosen the hex bolts (B) and adjust the blade guard mounting portion (stay) so that the spreader is aligned directly behind the blade. To check to be sure that the rip fence is parallel with the blade, secure the rip fence 2 - 3 mm (5/64" - 1/8" ) from the blade. Measure the distance (A) and (B) between the rip fence and blade. Take both measurements using the tooth marked with the crayon. These two measurements should be identical. If the rip fence is not parallel with the blade, proceed as follows: CAUTION: Be sure to adjust the rip fence so that it is parallel with the blade, or a dangerous kickback condition may occur. [. . . ] Do not use dado combinations wider than 13 mm (1/2"). After dadoing, ALWAYS replace the blade guard with the spreader back in its original position on the table saw. NEVER dado if there is vibration (flutter) or a strange noise. Feed work slowly, especially when cutting deep or wide grooves or dados. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA 2703#2702X1

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA 2703#2702X1 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag