User manual MAKITA 4323

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MAKITA 4323. We hope that this MAKITA 4323 user guide will be useful to you.

Lastmanuals help download the user guide MAKITA 4323.


Mode d'emploi MAKITA 4323
Download
Manual abstract: user guide MAKITA 4323

Detailed instructions for use are in the User's Guide.

[. . . ] Failure to do so may cause insufficient tightening of the blade, resulting in a serious injury. to install the blade , loosen the bolt on the blade holder with the hex wrench. With the blade teeth facing forward, insert the blade into the blade holder as far as it will go. Make sure that the back edge of the blade fits into the roller. [. . . ] For continuous operation, pull the trigger and then push in the lock button. To stop the machine from the locked position, pull the trigger fully, then release it. For 4323 only The machine speed can be infinitely adjusted between 500 and 3, 100 strokes per minute by turning the adjusting dial. Higher speed is obtained when the dial is turned in the direction of number 6; lower speed is obtained when it is turned in the direction of number 1. Refer to the table below to select the proper speed for the workpiece to be cut. However, the appropriate speed may differ with the type or thickness of the workpiece. In general, higher speeds will allow you to cut workpieces faster but the service life of the blade will be reduced. Loosen the bolt on the back of the machine base with the hex wrench, then move the machine base all the way back. Cutouts can be made with either of two methods A or B. A) Boring a starting hole: For internal cutouts without a lead-in cut from an edge, pre-drill a starting hole 12 mm or more in diameter. Insert the blade into this hole to start your cut. 13) B) Plung cutting: You need not bore a starting hole or make a lead-in cut if you carefully do as follows. Tilt the machine up on the front edge of the base, with the blade point positioned just above the workpiece surface. Apply pressure to the machine so that the front edge of the base will not move when you switch on the machine and gently lower the back end of the machine slowly. As the blade pierces the workpiece, slowly lower the base of the machine down onto the workpiece surface. CAUTION: The speed adjusting dial can be turned only as far as 6 and back to 1. Do not force it past 6 or 1, or the speed adjusting function may no longer work. To trim edges or make dimensional adjustments, run the blade lightly along the cut edges. Failure to do so may cause blade breakage, resulting in a serious injury. Turn the machine on and wait until the blade attains full speed. Then rest the machine base flat on the workpiece and gently move the machine forward along the previously marked cutting line. When cutting curves, advance the machine very slowly. [. . . ] now slide the rip fence to the desired cutting radius , and tighten the bolt to secure it in place. Then move the machine base all the way forward. To install the anti-splintering device, move the machine base all the way forward and insert it between the two protrusions of the machine base. CAUTION: The anti-splintering device cannot be used when making bevel cuts. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA 4323

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA 4323 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag