User manual MAKITA 4326

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MAKITA 4326. We hope that this MAKITA 4326 user guide will be useful to you.

Lastmanuals help download the user guide MAKITA 4326.


Mode d'emploi MAKITA 4326
Download

You may also download the following manuals related to this product:

   MAKITA 4326 4072D (655 ko)
   MAKITA 4326 ANNEXE 904 (788 ko)
   MAKITA 4326 ANNEXE 200 (1971 ko)
   MAKITA 4326 ANNEXE 954 (821 ko)

Manual abstract: user guide MAKITA 4326

Detailed instructions for use are in the User's Guide.

[. . . ] For European countries only Noise The typical A-weighted noise level determined according to 60745-2-11: Sound pressure level (LpA) : 86 dB(A) Sound power level (LWA) : 97 dB(A) Uncertainty (K) : 3 dB(A) Wear ear protection DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to jig saw safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury. Hold power tools by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. [. . . ] Make sure that the back edge of the blade fits into the roller. 2 CAUTION: Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigger fully, then release it. 3 The tool speed can be infinitely adjusted between 500 and 3, 100 strokes per minute by turning the adjusting dial. Higher speed is obtained when the dial is turned in the direction of number 6; lower speed is obtained when it is turned in the direction of number 1. refer to the table to select the proper speed for the workpiece to be cut. However, the appropriate speed 6 6 When not in use, store the hex wrench as shown in the figure to keep it from being lost. 13 Loosen the bolt on the back of the base with the hex wrench and slide the base all the way back. 7 Loosen the bolt on the back of the base with the hex wrench. Cutouts can be made with either of two methods A or B. 14 For internal cutouts without a lead-in cut from an edge, pre-drill a starting hole 12 mm or more in diameter. Insert the blade into this hole to start your cut. 15 You need not bore a starting hole or make a lead-in cut if you carefully do as follows. (1) Tilt the tool up on the front edge of the base with the blade point positioned just above the workpiece surface. (2) Apply pressure to the tool so that the front edge of the base will not move when you switch on the tool and gently lower the back end of the tool slowly. (3) As the blade pierces the workpiece, slowly lower the base of the tool down onto the workpiece surface. 8 CAUTION: Always wear safety goggles even when operating the tool with the dust cover lowered. Lower the dust cover to prevent chips from flying. However, when making bevel cuts, raise it all the way. Failure to do so may cause blade breakage, resulting in a serious injury. â· Advance the tool very slowly when cutting curves or scrolling. [. . . ] If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. To install the anti-splintering device, move the tool base all the way forward and fit it from the back of tool base. When you use the cover plate, install the anti-splintering device onto the cover plate. CAUTION: The anti-splintering device cannot be used when making bevel cuts. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA 4326

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA 4326 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag