User manual MAKITA 4340T

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MAKITA 4340T. We hope that this MAKITA 4340T user guide will be useful to you.

Lastmanuals help download the user guide MAKITA 4340T.


Mode d'emploi MAKITA 4340T
Download

You may also download the following manuals related to this product:

   MAKITA 4340T ANNEXE 164 (667 ko)

Manual abstract: user guide MAKITA 4340T

Detailed instructions for use are in the User's Guide.

[. . . ] Do not touch the blade or the workpiece immediately after operation; they may be extremely hot and could burn your skin. Always be sure that the tool is switched off and unplugged before installing or removing the blade. Always clean out all chips or foreign matter adhering to the blade and/or blade holder. Failure to do so may cause insufficient tightening of the blade, resulting in a serious injury. [. . . ] Refer to the table below to select the proper speed for the workpiece to be cut. However, the appropriate speed may differ with the type or thickness of the workpiece. In general, higher speeds will allow you to cut workpieces faster but the service life of the blade will be reduced. CAUTION: Do not look in the light or see the source of light directly. NOTE: Use a dry cloth to wipe the dirt off the lens of lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination. Failure to do so may cause blade breakage, resulting in a serious injury. Turn the tool on and wait until the blade attains full speed. Then rest the tool base flat on the workpiece and gently move the tool forward along the previously marked cutting line. When cutting curves, advance the tool very slowly. CAUTION: Always be sure that the tool is switched off and unplugged before tilting the tool base. With the tool base tilted, you can make bevel cuts at any angle between 0° and 45° (left or right). 9) Loosen the bolt on the back of the base with the hex wrench. Move the base so that the bolt is positioned in the center of the bevel slot in the base. CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing accessories. When repeatedly cutting widths of 160 mm or less, use of the rip fence will assure fast, clean, straight cuts. To install, insert the rip fence into the rectangular hole on the side of the tool base with the fence guide facing down. When cutting circles or arcs of 170 mm or less in radius, install the rip fence as follows. Insert the rip fence into the rectangular hole on the side of the tool base with the fence guide facing up. Insert the circular guide pin through either of the two holes on the fence guide. Screw the threaded knob onto the pin to secure the pin. now slide the rip fence to the desired cutting radius , and tighten the bolt to secure it in place. [. . . ] CAUTION: Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. To maintain product safety and reliability, repairs, maintenance or adjustment should be carried out by a Makita Authorized Service Center. Ratten för varvtalsreglering kan endast vridas till 5 och tillbaka till 1. CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA 4340T

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA 4340T will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag