User manual MAKITA 6328D

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MAKITA 6328D. We hope that this MAKITA 6328D user guide will be useful to you.

Lastmanuals help download the user guide MAKITA 6328D.


Mode d'emploi MAKITA 6328D
Download

You may also download the following manuals related to this product:

   MAKITA 6328D ANNEXE 352 (138 ko)

Manual abstract: user guide MAKITA 6328D

Detailed instructions for use are in the User's Guide.

[. . . ] 1 2 3 4 5 6 7 8 Button Battery cartridge Charging light Battery charger Tighten Sleeve Ring Switch trigger 9 10 11 12 13 14 15 16 Reversing switch lever A side B side Clockwise Counterclockwise Low speed High speed Speed change lever 17 18 19 20 21 22 Adjusting ring Graduations Drill marking Pointer Screw Set plate Due to our continuing program of research and development, the specifications herein are subject to change without notice. â· Note: Specifications may differ from country to country. Intended use The tool is used for drilling and screw driving in wood, metal and plastic. Safety hints For your own safety, please refer to the enclosed safety instructions. [. . . ] â· When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely and recharging a couple of times. â· When you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, let it cool off. Then re-insert it and try to charge it once more. â· When you charge a new battery cartridge or a battery cartridge which has not been used for a long period, sometimes the charging light will go out soon. if this occurs , remove the battery cartridge and re-insert it. If the charging light goes out within one minute even after repeating this procedure a couple of times, the battery cartridge is dead. 3) Plug the battery charger into the proper A/C voltage source. The charging light will flash in green color. Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective markings on the battery charger. insert the cartridge fully into the port so that it rests on the charger port floor. When the battery cartridge is inserted, the charging light color will change from green to red and charging will begin. The charging light will remain lit steadily during charging. When the charging light color changes from red to green, the charging cycle is complete. If you leave the battery cartridge in the charger after the charging cycle is complete, the charger will switch into its "trickle charge (maintenance charge)" mode which will last approximately 24 hours. After charging, unplug the charger from the power source. Never use it for other purposes or for other manufacturer's batteries. â· When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge. This is a normal condition and does not indicate a problem. You can recharge the battery cartridge fully after discharging it completely and recharging a couple of times. â· If you charge a battery cartridge from a just-operated tool or a battery cartridge which has been left in a location exposed to direct sunlight or heat for a long time, the charging light may flash in red color. [. . . ] â· Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a centerpunch and hammer at the point to be drilled. place the point of the bit in the indentation and start drilling. Use a cutting lubricant when drilling metals. The exceptions are iron and brass which should be drilled dry. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA 6328D

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA 6328D will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag