User manual MAKITA 6807

[. . . ] Screwdriver MODEL 6807 003556 DOUBLE INSULATION INSTRUCTION MANUAL WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. SPECIFICATIONS Model Self drilling screw Capacities Drywall screw High Low High Low High Low 6807 6 mm (1/4") 8 mm (5/16") 5 mm (3/16") 5 mm (3/16") 0 - 2, 200/min. 318 mm (12-1/2") 2. 0 kg (4. 4 lbs) No load speed (RPM) Overall length Net weight · Manufacturer reserves the right to change specifications without notice. · Specifications may differ from country to country. GENERAL SAFETY RULES (For All Tools) USA002-2 WARNING: Read and understand all instructions. [. . . ] Accessories that may be suitable for one tool, may become hazardous when used on another tool. SERVICE 23. Tool service must be performed only by qualified repair personnel. Service or maintenance performed by unqualified personnel could result in a risk of injury. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance instructions may create a risk of electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table 1 shows the correct size to use depending on cord length and nameplate ampere rating. The smaller the gage number, the heavier the cord. Table 1: Minimum gage for cord Ampere Rating More Than 0 6 10 12 Not More Than 6 10 12 16 18 18 16 14 Volts 120 V 25 ft. AWG 16 16 16 12 16 14 14 12 14 12 Not Recommended SPECIFIC SAFETY RULES USB004-2 DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to screwdriver safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury. 1. Hold tool by insulated gripping surfaces when performing an operation where the cutting tool may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. Be sure no one is below when using the tool in high locations. Keep hands away from rotating parts. 4 5. Do not touch the bit or the workpiece immediately after operation: they may be extremely hot and could burn your skin. SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. SYMBOLS The followings show the symbols used for tool. V . . . . . . . . . . . . . . . . . . . . . . . alternating current USD201-2 n . . . . . . . . . . . . . . . . . . . . no load speed ° . . . . . . . . . . . . . . . . . . . . Class II Construction . . . /min. . . . . . . . . . . . . . . . revolutions or reciprocation per minute 5 FUNCTIONAL DESCRIPTION · CAUTION: Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 003557 Depth adjustment The depth can be adjusted by turning the locking sleeve. Turn it in "A" direction for less depth and in "B" direction for more depth. One full turn of the locking sleeve equals 1. 5 mm (1/16") change in depth. 1 A B 1. Locking sleeve 003558 1 Adjust the locking sleeve so that the distance between the tip of the locator and the screw head is approximately 1 mm (3/64") as shown in the figure. Drive a trial screw into your material or a piece of duplicate material. [. . . ] This could damage a workpiece or cause an injury. Make sure that the bit is inserted straight in the screw head, or the screw and/or bit may be damaged. · · MAINTENANCE · CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. ACCESSORIES CAUTION: · These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose. [. . . ]