User manual MAKITA 8402VD

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MAKITA 8402VD. We hope that this MAKITA 8402VD user guide will be useful to you.

Lastmanuals help download the user guide MAKITA 8402VD.


Mode d'emploi MAKITA 8402VD
Download
Manual abstract: user guide MAKITA 8402VD

Detailed instructions for use are in the User's Guide.

[. . . ] Cordless Hammer Drill Equipped with electric brake MODEL 8402VD MODEL 8402VDW With Fast Charger INSTRUCTION MANUAL Capacities Steel 10" 1318") Wood Concrete 10" 1318") Wood screw No load speed IRPM) - Blows per minute - Overall length 260 m m 110-114") Net weight 1. 7 k g (3. 7 Ibs) 12" 1112") 3 . 8 m m x 20" (118" x 314") io'ooo Battery Cartridge 9000 Voltage 9. 6 V Charging time 1 Hr. Model DC9700 Fast Charger Input A. C. 9. 6 V IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PERSONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. Cluttered areas and benches invite injuries. [. . . ] Do not incinerate the Battery Cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. ADDITIONAL SAFETY RULES 1. Be aware that this tool is always in an operating condition, because it does not have t o be plugged into an electrical outlet. It is also highly recommended that you wear a dust mask, ear protectors and thickly padded gloves. Under normal operation, the tool is designed t o produce vibration. The screws can come loose easily, causing a breakdown or accident. Check tightness of screws carefully before operation. Be sure no one is below when using the tool in high locations. When drilling into walls, floors or wherever "live" electrical wires may be encountered, DO NOT TOUCH ANY METAL PARTS OF THE TOOL!Hold the tool by the insulated grasping surfaces to prevent electric shock if you drill into a "live" wire. 9. Do not touch the bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin. SAVE THESE INSTRUCTIONS. 5 Installing or removing battery cartridge . Always switch off the tool before insertion or removal of the battery cartridge. . To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. 0 Set plate / To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Be sure t o close the set plate fully before using the tool. 0 Do not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it i s not being inserted correctly. Charging Plug the fast charger into your power source. Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective markings on the fast charger. Insert the cartridge fully into the port so that it rests on the charger port floor. The charging light will come on and charging will begin. If the charging light does not come on, press the reset button (yellow) first, then the start button (red). I f the charging light goes out within 10 seconds even after pressing the reset button and start button a couple of times, the battery cartridge is dead. (CAUTION: Wait for more than 5 seconds after the charging light goes out to press the reset button again. ) Replace it with a new one. When the charging light goes out after about one hour, you may remove the fully charged battery cartridge. After charging, unplug the charger from the power source. CAUTION : 0 Your new battery cartridge is not charged. You will need t o charge it before use. Do not keep the button pressed in with tape, etc. [. . . ] The guide screw makes drilling easier by pulling the bit into the workpiece. Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a centerpunch and hammer a t the point to be drilled. Place the point of the bit in the indentation and s t a r t drilling. Use a cutting lubricant when drilling metals. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA 8402VD

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA 8402VD will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag