User manual MAKITA 9523NB

[. . . ] If in doubt, wear the protective equipment. Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Use only wheels with correct size and wheels having a maximum operating speed at least as high as the highest No Load Speed marked on the tool's nameplate. When using depressed center wheels, be sure to use only fiberglassreinforced wheels. [. . . ] Do not touch the workpiece immediately after operation; it may be extremely hot and could burn your skin. Position the tool so that the power cord always stays behind the tool during operation. If working place is extremely hot and humid, or badly polluted by conductive dust, use a shortcircuit breaker (30 mA) to assure operator safety. Do not use the tool on any materials containing asbestos. Ensure that ventilation openings are kept clear when working in dusty conditions. If it should become necessary to clear dust, first disconnect the tool from the mains supply (use non metallic objects) and avoid damaging internal parts. Important: Always be sure that the tool is switched off and unplugged before installing or removing the wheel guard. Mount the wheel guard with the tab on the wheel guard band aligned with the notch on the bearing box. Then rotate the wheel guard 180° clockwise (for 9523NB) or counterclockwise (for 9524NB and 9525NB). CAUTION: Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Whenever carbon brushes must be replaced, they cut out the tool automatically. When this occurs, replace both carnon brushes at the same time. To maintain product safety and reliability, repairs, maintenance or adjustment should be carried out by a Makita Authorized Service Center. For 9524NB and 9525NB For your own safety, always use the side grip. The side grip can be installed on either side of the tool. Important: Always be sure that the tool is switched off and unplugged before installing or removing the wheel. mount the inner flange onto the spindle. Fit the wheel on over the inner flange and screw the lock nut onto the spindle. Press the shaft lock to prevent spindle rotation, then use the lock nut wrench to tighten the lock nut securely. WARNING: Only actuate the shaft lock when the spindle is not moving. [. . . ] The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. Wheel cover Couvercle de meule Schutzhaube Protezione disco Beschermkap Cubierta de disco Cobertura do disco Skærm Rondellskydd Skivedeksel Laikan suojus µµ Inner flange Flasque intérieur Innenflansch Flangia interna Binnenflens Brida interior Anilha centradora Indvendig flange Inre fläns Indre flense Sisälaippa Depressed center wheels Meules à centre concave Trennschleifscheiben Dischi a centro depresso Schijven met verzonken asgat Discos de centro rebajado Discos de centro deprimido Forkrøppet slibeskive Rondeller med försänkt nav Nedtrykte minuttskiver Keskeltä ohennetut laikat µµ Lock nut Ecrou de sécurité Sicherungsmutter Controdado Sluitmoer Contratuerca Porca de bloqueio Flangemøtrik Låsmutter Sikringsmutter Lukitusmutteri µ µ Rubber pad Coussin de caoutchouc Gummiteller Cuscinetto di gomma Rubberkussen Plato de caucho Almofada de borracha Elastisk bagskive Gummisula Gummiunderlag Kumityyny µ We declare under our sole responsibility that this product is in compliance with the following standards or standardized documents, HD400, EN50144, EN55014, EN61000 in accordance with Council Directives, 73/23/EEC, 89/336/EEC and 98/37/EC. The typical A-weighted sound pressure level is 83 dB (A). [. . . ]