User manual MAKITA 9523NBHK

[. . . ] Angle Grinder 100 mm (4") MODEL 9523NBH 115 mm (4-1/2") MODEL 9524NB 125 mm (5") MODEL 9525NB DOUBLE INSULATION INSTRUCTION MANUAL WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. w w w. c o m SPECIFICATIONS Model No load speed (RPM) Overall length Net weight Spindle thread 9523NBH 11, 000/min 256 mm (10") 1. 4 kg (3. 1 lbs) M10 x 1. 25 9524NB 11, 000/min 256 mm (10") 1. 4 kg (3. 1 lbs) 5/8" 9525NB 10, 000/min 256 mm (10") 1. 4 kg (3. 1 lbs) 5/8" · Manufacturer reserves the right to change specifications without notice. · Specifications may differ from country to country. GENERAL SAFETY RULES (For All Tools) USA002-2 WARNING: Read and understand all instructions. [. . . ] The tool may be damaged. 1 Press the shaft lock to prevent spindle rotation when installing or removing accessories. 1. Shaft lock 001033 Switch action · CAUTION: Before plugging in the tool, always check to see that the slide switch actuates properly and returns to the "OFF" position when the rear of the slide switch is depressed. Switch can be locked in "ON" position for ease of operator comfort during extended use. Apply caution when locking tool in "ON" position and maintain firm grasp on tool. 1 · 1. Slide switch To start the tool, slide the slide switch toward the "I (ON)" position. For continuous operation, press the front of the slide switch to lock it. To stop the tool, press the rear of the slide switch, then slide it toward the "O (OFF)" position. ASSEMBLY · CAUTION: Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 001051 Installing side grip (handle) · CAUTION: Always be sure that the side grip is installed securely before operation. Screw the side grip securely on the position of the tool as shown in the figure. 6 001060 Installing or removing wheel guard · CAUTION: When using a depressed center grinding wheel/Multidisc, flex wheel, wire wheel brush or cut-off wheel, the wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator. 9523NBH 1 2 3 1. Screw 001062 Mount the wheel guard with the protrusion on the wheel guard band aligned with the notch on the bearing box. Then rotate the wheel guard around 180 degrees. Be sure to tighten the screw securely. 1 2 3 9524NB, 9525NB To remove wheel guard, follow the installation procedure in reverse. 1. Screw 001070 1 2 3 Installing or removing depressed center grinding wheel/Multi-disc · WARNING: Always use supplied guard when depressed center grinding wheel/Multi-disc is on tool. Wheel can shatter during use and guard helps to reduce chances of personal injury. 1. Depressed center grinding wheel/ Multi-disc 3. Inner flange 001082 Mount the inner flange onto the spindle. Fit the wheel/disc on the inner flange and screw the lock nut onto the spindle. To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise. To remove the wheel, follow the installation procedure in reverse. 1 2 1. Shaft lock 7 001094 1 2 3 4 Installing or removing flex wheel (optional accessory) · WARNING: Always use supplied guard when flex wheel is on tool. Wheel can shatter during use and guard helps to reduce chances of personal injury. 1. 4. Lock nut Flex wheel Plastic pad Inner flange Follow instructions for depressed center grinding wheel/ Multi-disc but also use plastic pad over wheel. See order of assembly on accessories page in this manual. 001105 1 2 3 Installing or removing abrasive disc (optional accessory) NOTE: · Use sander accessories specified in this manual. [. . . ] Omaha, NE 68127 (402) 597-2925 OREGON 828 19th Avenue. , N. W. Portland, OR 97209 (503) 222-1823 WASHINGTON 22220 84th Ave. A Kent, WA 98032 (253) 395-8055 KANSAS 8819 W. Overland Park, KS 66212 (913) 642-1111 NEVADA 3375 S. [. . . ]