User manual MAKITA BCM4300

[. . . ] Instruction Manual Original Instruction Manual BCM2600 BCM3300 BCM4300 BCM2310 BCM2610 BCM3310 Important: Read this instruction manual carefully before putting the brushcutter into operation and strictly observe the safety regulations!Keep this Instruction Manual! Thank you for choosing a MAKITA product! We trust that you will be a satisfied customer. By choosing a MAKITA you have chosen one of the most advanced brushcutters. With their two-stroke gasoline engines the brushcutters can be used anywhere, and with their fuel pump (primer) they are unusually easy to start. [. . . ] Use only original MAKITA spares and accessories. The use of non-MAKITA spares, accessories, or cutting tools increases the risk of accident. MAKITA will not accept any liability for accidents or damage caused by the use of non-approved cutting tools and fixing devices of cutting tools, or accessories. 18 First Aid A first-aid kit should always be nearby as a precaution in the event of an accident. Immediately replace any items taken from the first aid kit. When calling for help, give the following information: Place of accident, what happened, number of persons injured, nature of injuries, your name. NOTE Individuals with poor circulation who are exposed to excessive vibration may experience injury to blood vessels or the nervous system. Vibration may cause the following symptoms to occur in the fingers, hands or wrists: "Falling asleep" (numbness), tingling, pain, stabbing sensation, alteration of skin colour or of the skin. If any of these symptoms occur, see a physician! 19 7 Technical Data Displacement Bore Stroke Rated capacity per ISO 8893 Operating speed Maximum engine speed with one-part metal cutting tool 1) 2310 | 2610 | 3310 cm3 mm mm kW rpm rpm rpm rpm Type Type Type mm dB(A) dB(A) m/s2 m/s2 m/s2 m/s2 kg/h g/kWh l 22. 6 | 25. 6 | 32. 6 31 | 33 | 36 30 | 30 | 32 0. 7 | 0. 8 | 0. 97 8, 000 | 8, 000 | 7, 500 7, 370 I 7, 370 I 8, 100 10, 000 3, 000 I 3, 000 I 2, 500 2600 | 3300 | 4300 25. 6 | 32. 6 | 42. 7 33 | 36 | 40 30 | 32 | 34 0. 8 | 0. 97 | 1. 27 8, 000 | 7, 500 | 7, 500 7, 370 I 8, 100 I 7, 370 10, 000 3, 000 I 2, 500 I 2, 500 Maximum spindle speed with one-part metal cutting tool 1) Idling speed Carburetor Ignition system Spark plug Electrode gap Sound power level LWA, eq per ISO 10884 2) 4) Sound pressure level LpA, eq at the workplace per ISO 7917 2) 5) Vibration acceleration ahv, eq per ISO 7916 2) 6) - Right handle (idling speed/maximum speed) - Left handle (idling speed/maximum speed) - Round handle (idling speed/maximum speed) - Handle on shaft (idling speed/maximum speed) Fuel consumption per ISO 8893 3) Specific consumption per ISO 8893 3) Fuel tank capacity Mixture ratio (fuel / MAKITA two-stroke oil) - when using MAKITA oil - when using Aspen Alkylat (two-stroke fuel) - when using other oils (quality grade: JASO FC or ISO EGD) Gear ratio Weight (not including guard, cutting tool and fuel) 1) 2) 3) diaphragm carburetor diaphragm carburetor electronic electronic NGK BPMR 8Y 0. 6 - 0. 7 106. 8 | 107. 8 | 109 94. 9 | 95. 1 | 97. 1 NGK BPMR 8Y 0. 6 - 0. 7 99. 5 | 100. 5 | 102 89. 9 | 92 | 91. 4 5. 1 / 5. 7 | 2. 1 / 6. 2 | 4. 8 / 5. 5 4. 0 / 6. 2 | 5. 0 / 5. 3 | 5. 3 / 6. 5 7. 5 / 6. 1 | 4. 6 / 9. 5 | 4. 7 / 6. 5 4. 8 / 8. 1 | 4. 4 / 6. 0 | 6. 3 / 7. 8 0. 35 | 0. 36 | 0. 44 500 | 450 | 454 0. 6 | 0. 6 | 0. 8 50:1 50:1 (2%) 50:1 0. 36 | 0. 44 | 0. 49 450 | 454 | 386 0. 6 | 0. 8 | 0. 9 50:1 50:1 (2%) 50:1 14:19 | 14:19 | 14:19 5. 9 | 6. 7 | 7. 9 kg 14:19 | 14:19 | 17:21 5. 1 | 5. 1 | 5. 9 The maximum rated speed of the trimmer head is not exceeded when using a MAKITA trimmer head. Figures derived in equal part from idle and top-speed operation (per EN-ISO 11806). 6) Uncertainty K = 2 m/s2. Components 1 Cutting tool 2 Gear box 3 Guard (Cutter guard) 4 Shaft tube 5 Handle 6 Throttle (throttle trigger) Type plate (BCM2600) BCM2600 2008 123456 Serial number Year of manufacture 22045 Hamburg Germany Shown: BCM2600 000. 000. 000 Indicate when ordering spare parts! 7 Combination "start/stop" (O/I) switch, half-throttle lock 8 Safety locking button (throttle trigger lockout) 9 Bowden cable guide 10 Tube handle holder 11 Stop knob for halfway throttle 12 Harness eyelet (suspension point) 13 Fuel tank cap 14 Spark plug cover 15 Starter grip 16 Type plate 17 Choke lever 18 Harness 8 PUTTING INTO OPERATION STOP CAUTION: When working on the brushcutter always be absolutely certain to switch off the engine, pull the spark plug cap and wear protective gloves! IMPORTANT: Do not start the brushcutter until fully assembled and inspected! Installing the handle (BCM2600, BCM3300, BCM4300) A Loosen screws (A/1) and unscrew about 1-2 mm. Push the grips (A/2) into the grip mounting, as shown in the illustration. Tighten the screws only enough to hold the grips while leaving them able to be turned for final positioning. - B Push the handle about 10 to 20° forward and tighten the bolts (A/1). Attach the bowden cable to the shaft tube using the cable ties (B/3) found in the enclosed pack. NOTE: The handle must be tilted to accommodate the operator, so the exact angle will depend on the operator's body size. For easiest operation the elbows should be slightly bent, with the wrists straight. Installing the handle (BCM2310, BCM2610, BCM3310) C Take the bolts and nuts (C/4, 5) and grip bracket (C/7) from the enclosed pack. Attach the handle retainer plate (C/7) with bolts (C/4) and nuts (C/5). Set the right distance between the throttle grip (C/8) and hand grip, and tighten screws (C/4). 9 Installing the cutter guard Important: Safety regulations and your own safety make it imperative to use the right cutter guard with a given cutting tool! Warning: Use only the cutting tools shown here!It is not permitted to use other cutting tools as this can increase danger of accidents and cause damage to the equipment! Tool/guard combinations for the BCM2600 / BCM3300 / BCM4300 Cutting tool 4-tooth star blade: Part no. 362 224 140 Outside diameter: 230 mm (9"), arbour: 25. 4 mm (1") Cutter guard Part no. 351 504 101 2-line trimmer head Part no. 351 504 102 Install the guard extension Tool/guard combinations for the BCM2310 / BCM2610 / BCM3310 Cutting tool 2-line trimmer head Part no. 351 504 102 Install the guard extension Mounting the cutter guard Hook the hood (A/5) by the cutout (A/1) on the lug (A/2). [. . . ] 1 2 3 4 5 6 6 7 9 10 11 12 - MAKITA-No. 351 050 230 352 400 040 351 400 800 351 410 110 362 224 140 351 510 013 351 510 023 351 502 030 351 010 154 351 010 151 351 010 152 351 010 153 369 224 670 369 224 672 Qty 1 1 1 1 1 1 1 1 1 1 1 1 1 1 Description Tank cap cpl. Suction head Air filter Spark plug NGK BPMR 8Y 4-tooth star blade Locknut (for BCM2600/3300) Locknut (for BCM4300) 2-line trimmer head, cpl. Open wrench 8/10 Allen key, 4 mm Allen key, 5 mm Combination tool, AF 17/19 Trimmer line, 2. 4 mm dia. [. . . ]