User manual MAKITA BFT083F

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MAKITA BFT083F. We hope that this MAKITA BFT083F user guide will be useful to you.

Lastmanuals help download the user guide MAKITA BFT083F.


Mode d'emploi MAKITA BFT083F
Download
Manual abstract: user guide MAKITA BFT083F

Detailed instructions for use are in the User's Guide.

[. . . ] Do not touch the bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. It may result in a risk of overheating, possible burns and even an explosion. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. [. . . ] Insert it fully until the red part cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. The lamp on the tool shows the following functions. For approximately one second after auto-stop fastening, the tool does not start even if the switch trigger is pulled. Insufficient fastening has been performed when the switch trigger has released before reaching the preset fastening torque. Lights up in green for approximately one second. Status This indicates the appropriate time to replace the battery cartridge when the battery power becomes low. This function works when the battery power is almost used up. This function works to check the proper operation of the LED indicator, light and beeper when a battery cartridge has been inserted into the tool. This function works when an abnormal drop of the battery voltage occurs for some reason, and the tool stops. This function works when the temperature of the controller goes up very highly, and the tool stops. This function works to avoid the tool's immediate start upon insertion of battery cartridge into the tool with the switch trigger being pulled. Action to be taken Replace the battery with fully charged one Replace the battery with fully charged one Lights up first in green, next red. Replace the battery with fully charged one Remove the battery cartridge immediately and cool the tool down. First remove the battery cartridge from the tool. Rotate the ring in the front of the tool by hand so that a hole can be seen below the ring. Insert the pin of the adjust grip into the hole in the front of the tool. And then, turn the adjust grip clockwise to set a greater fastening torque, and counterclockwise to set a smaller fastening torque. Align the yellow line with your desired number on the fastening torque scale. Insert the battery cartridge and be sure that a fastening torque has been set up by using a fastening torque tester. Rotate the ring in the front of the tool and then tighten the screw to secure the ring. nOTE: · Numbers on the fastening torque scale are a guideline to set up your desired fastening torque. [. . . ] Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA BFT083F

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA BFT083F will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag