User manual MAKITA BTD145 ANNEXE 381

[. . . ] ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Impact Driver BTD133 BTD145 011185 IMPORTANT: Read Before Using. 1 ENGLISH (Original instructions) SPECIFICATIONS Model Machine screw Capacities Standard bolt High tensile bolt Hammer mode (Hard) No load speed (min-1) Hammer mode (Medium) Hammer mode (Soft) Hammer mode (Hard) Impacts per minute Hammer mode (Medium) Hammer mode (Soft) Overall length Net weight (with battery cartridge) Rated voltage BTD133 4 mm - 8 mm 5 mm - 14 mm 5 mm - 12 mm 0 - 2, 400 0 - 1, 800 0 - 1, 100 0 - 3, 200 0 - 2, 600 0 - 1, 100 With one-touch bit holder 139 mm Without one-touch bit holder 140 mm 1. 4 kg D. C. 14. 4 V BTD145 4 mm - 8 mm 5 mm - 14 mm 5 mm - 12 mm 0 - 2, 600 0 - 2, 000 0 - 1, 300 0 - 3, 400 0 - 2, 800 0 - 1, 300 With one-touch bit holder 139 mm Without one-touch bit holder 140 mm 1. 3 kg D. C18 V · Due to our continuing programme of research and development, the specifications herein are subject to change without notice. · Specifications and battery cartridge may differ from country to country. · Weight, with battery cartridge, according to EPTA-Procedure 01/2003 END004-4 Model BTD133 Sound pressure level (LpA) : 92 dB(A) Sound power level (LWA) : 103 dB(A) Uncertainty (K) : 3 dB(A) Model BTD145 Sound pressure level (LpA) : 93 dB(A) Sound power level (LWA) : 104 dB(A) Uncertainty (K) : 3 dB(A) Wear ear protection ENG900-1 Symbols The following show the symbols used for the equipment. Be sure that you understand their meaning before use. [. . . ] Keep handles dry, clean and free from oil and grease. GEB054-1 CORDLESS IMPACT DRIVER SAFETY WARNINGS 1. Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock. Be sure no one is below when using the tool in high locations. Hold the tool firmly. 2. 3. 4. Wear ear protectors. Tips for maintaining maximum battery life 1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery cartridge when you notice less tool power. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life. Charge the battery cartridge with room temperature at 10 C - 40 C (50 F - 104 F). Let a hot battery cartridge cool down before charging it. SAVE THESE INSTRUCTIONS. WARNING: DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. ENC007-6 2. 3. IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CARTRIDGE 1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50 C (122 F). Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. [. . . ] · Hold the tool pointed straight at the screw. · If the hammering force is too strong you tighten the screw for a time longer than shown in the figures, the screw or the point of the driver bit may be overstressed, stripped, damaged, etc. Before starting your job, always perform a test operation to determine the proper fastening time for your screw. 9 Proper fastening torque Proper fastening torque 80 (816) The fastening torque is affected by a wide variety of factors including the following. [. . . ]