User manual MAKITA DCS510-18

[. . . ] Always follow safety precautions in the Owner's and Safety Manual. The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. A, Inc warrant to the initial retail purchaser and each subsequent owner, that this utility equipment was designed, built, and equipped to conform at the time of initial sale to all applicable regulations of the U. Environmental Protection Agency (EPA), and that the engine is free of defects in materials and workmanship which would cause this engine to fail to conform with EPA regulations during its warranty period. [. . . ] Tighten all nuts, bolts and screws except the carburetor adjustment screws after each use. Keep spark plug and wire connection tight and clean. Store saws in a high or locked place, away from children. Only properly trained professionals should work in an area where the logs, limbs and roots are tangled (i. Drag the logs into a clear area before cutting. 1 Handle 2 Filter cover 3 Filter hood clip 4 Tubular handle 5 Hand guard (release for chain brake) 6 Muffler with spark arrester screen 7 Spike bar (toothed stop for holding saw steady against wood) 8 Chain tensioning screw 9 Retaining nuts 10 Chain catch 11 Sprocket guard 12 Decompression valve 13 Adjusting screw for oil pump (bottom side) 16 Starter grip 17 Combination switch (Choke / Start / Stop) 18 Throttle lever 19 Safety locking button 20 Rear hand guard 21 Fuel tank cap 22 Fan housing with starting assembly 23 Oil tank cap 24 Guide bar 25 Chain (Blade) Power at speed 1) Max. Engine speed with bar and chain Idling speed Coupling speed Sound Pressure Level at the operator`s ear at full load according to ANSI B 175. Load per ISO 7293 1) Fuel tank capacity Chain oil tank capacity Mixture ratio (fuel/two-stroke oil) - when using MAKITA oil - when using Aspen Alkalyt (two-stroke fuel) - when using other oils Chain brake Sprocket pitch Number of teeth Chain type Pitch / gauge Guide bar, length of a cut Guide-bar type Weight (fuel tank empty, without chain, guide bar and accessories) WARNING: This chain saw is capable of severe kickback that coult result in serious injury to the user. Do not operate this chain saw unless you have extraordinary cutting needs and experience and specialized training for dealing with kickback. Chain saws with significantly reduced kickback potential are available. Before doing any work on the guide bar or chain, always switch off the engine and pull the plug cap off the spark plug (see "Replacing the spark plug"). Start the chain saw only after having assembled it completely and inspected. Use the universal wrench delivered with the chain saw for the following work. Put the chain saw on a stable surface and carry out the following steps for mounting the guide bar and saw chain: Release the chain brake by pulling the hand guard (1) in direction of arrow. Turn chain tensioning screw (4) to the left (counter-clockwise) until the pin (5) of the chain tensioner is underneath the threaded pin (6). CAUTION: Do not insert the chain between the chain sprocket and the disc. Guide the chain from above about halfway into the groove (10) on the guide bar. place the chain over the chain catch (11) on the bottom. CAUTION: Note that the cutting edges along the top of the chain must point in the direction of the arrow!Pull the chain (9) around the sprocket nose (12) of the guide bar in the direction of the arrow. Tighten the nuts (2) only hand-tight to begin with. Turn the chain tensioning screw (4) to the right (clockwise) until the saw chain catches in the groove on the lower side of the guide bar (see circle). [. . . ] He will also have the spare part lists to determine the required spare part numbers, and will be constantly informed about the latest improvements and spare part innovations. Please bear in mind that if parts other than original MAKITA spare parts are used, this will automatically invalidate the MAKITA product guarantee. MAKITA guarantees the highest quality and will therefore reimburse all costs for repair by replacement of damaged parts resulting from material or production faults occurring within the guarantee period after purchase. Please note that in some countries particular guarantee conditions may exist. [. . . ]