User manual MAKITA HM1101C

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MAKITA HM1101C. We hope that this MAKITA HM1101C user guide will be useful to you.

Lastmanuals help download the user guide MAKITA HM1101C.


Mode d'emploi MAKITA HM1101C
Download
Manual abstract: user guide MAKITA HM1101C

Detailed instructions for use are in the User's Guide.

[. . . ] Do not point the tool at any one in the area when operating. The bit could fly out and injure someone seriously. Do not touch the bit or parts close to the bit immediately after operation; they may be extremely hot and could burn your skin. Some material contains chemicals which may be toxic. [. . . ] Loosen the side grip by turning it counterclockwise, swing it to the desired position and then tighten it by turning clockwise. The blows per minute can be adjusted just by turning the adjusting dial. This can be done even while the tool is running. the dial is marked 1 (lowest speed) to 5 (full speed). Refer to the table below for the relationship between the number settings on the adjusting dial and the blows per minute. Clean the bit shank and apply bit grease before installing the bit. Turn the bit and push it in until it engages. Pull the releasing cover down a couple of times. Turn the bit and push it in until it engages. 8) After installing, always make sure that the bit is securely held in place by trying to pull it out. 9) To remove the bit, pull the releasing cover down all the way and pull the bit out. The speed adjusting dial can be turned only as far as 5 and back to 1. Do not force it past 5 or 1, or the speed adjusting function may no longer work. for Model HM1111C only NOTE: · Blows at no load per minute becomes smaller than those on load in order to reduce vibration under no load, but this does not show trouble. Once operation starts with a bit against concrete, blows per minute increase and get to the numbers as shown in the table. When temperature is low and there is less fluidity in grease, the tool may not have this function even with the motor rotating. The bit can be secured at 12 different angles. To change the bit angle, slide the change ring forward, then turn the change ring to change the bit angle. The change ring cannot turn when the bit is not installed on the tool. Always use the D-shaped side handle or side grip (auxiliary handle) and firmly hold the tool by both Dshaped side handle or side grip and switch handle during operations. Turn the tool on and apply slight pressure on the tool so that the tool will not bounce around, uncontrolled. Pressing very hard on the tool will not increase the efficiency. [. . . ] ⷠThe declared vibration emission value may also be used in a preliminary assessment of exposure. wARNING: · The vibration emission during actual use of the power tool can differ from the declared emission value depending on the ways in which the tool is used. ⷠBe sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time). For European countries only ENH101-14 EC Declaration of Conformity We Makita Corporation as the responsible manufacturer declare that the following Makita machine(s): Designation of Machine: Demolition Hammer Model No. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA HM1101C

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA HM1101C will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag