User manual MAKITA HS300D

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MAKITA HS300D. We hope that this MAKITA HS300D user guide will be useful to you.

Lastmanuals help download the user guide MAKITA HS300D.


Mode d'emploi MAKITA HS300D
Download

You may also download the following manuals related to this product:

   MAKITA HS300D PARTS LIST (575 ko)

Manual abstract: user guide MAKITA HS300D

Detailed instructions for use are in the User's Guide.

[. . . ] Cutting depth No load speed (min-1) Overall length Net weight Rated voltage • Specifications and battery cartridge may differ from country to country. € Weight, with battery cartridge, according to EPTA-Procedure 01/2003 ENE028-1 HS300D 85 mm at 90° at 45° 25. 8 V • Due to our continuing programme of research and development, the specifications herein are subject to change without notice. Intended use The tool is intended for performing lengthways and crossways straight cuts and mitre cuts with angles in wood while in firm contact with the workpiece. [. . . ] Check the operation of the lower guard spring. If the guard and the spring are not operating • 011400 15. Push the saw forward at a speed so that the blade cuts without slowing. Forcing the saw can cause uneven cuts, loss of accuracy, and possible kickback. Use extra caution when cutting damp wood, pressure treated lumber, or wood containing knots. Adjust speed of cut to maintain smooth advancement of tool without decrease in blade speed. Do not attempt to remove cut material when blade is moving. Wait until blade stops before grasping cut material. Inspect for and remove all nails from lumber before cutting. Place the wider portion of the saw base on that part of the workpiece which is solidly supported, not on the section that will fall off when the cut is made. 1 illustrates the RIGHT way to cut off the end of a board, and Fig. If the 5 workpiece is short or small, clamp it down. Gum and wood pitch hardened on blades slows saw and increases potential for kickback. Keep blade clean by first removing it from tool, then cleaning it with gum and pitch remover, hot water or kerosene. Wear a dust mask and hearing protection when use the tool. WARNING: DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. [. . . ] € When the remaining battery capacity gets low: Recharge the battery cartridge. Simply slide the rip fence up snugly against the side of the workpiece and secure it in position with the screw on the front of the base. 9 When not in use, store the hex wrench as shown in the figure to keep it from being lost. MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA HS300D

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA HS300D will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag