User manual MAKITA JIG SAW 4305T

[. . . ] Jig Saw MODEL 4304T Variable Speed MODEL 4305T Variable Speed INSTRUCTION MANUAL ~ 43041 4305T DOUBLE INSULATION SPECIFICATIONS Model Length of stroke Wood Max. cutting capacities Aluminum Mild Steel 10mm (318") Strokes per minute Overall length 249 mm 19-3/4"1 287 mm (11-5/16', ) Net weight 2. 4 kg (5. 3 Ibs) 4304T . 4305T 26" (1") 135" (5-5116") (:g/yg') 500 ~ 3, 000 Manufacturer reserves the right t o change specifications without notice. Note: Specifications may differ from country t o country. WARNING: For your personal safety, READ and UNDERSTAND before using. [. . . ] Open the clamp a l i t t l e more than the thickness of the blade to be installed. With the blade teeth facing forward, insert the blade into the blade holder as far as it will go. Make sure that the back edge of the blade fits properly into the groove of the ro Iler . With the blade held against the blade holder, rotate the blade installing lever in the @ direction to tighten the clamp. Blade holder Roller 5. With the blade installing lever held ii" this position, move it in the @ direction. Then rotate the blade installing lever in the @ direction to return it to i t s original position. 5 For 4305T 1. Press the button to raise the blade installing knob. Rotate the blade installing knob in the 0 direction and the clamp on the blade holder will open. Open the clamp a l i t t l e more than the thickness of the blade to be installed. With the blade teeth facing forward, insert the blade into the blade holder as far as it will go. Make sure that the back edge of the blade f i t s properly into the groove of the roller. With the blade held against the blade holder, rotate the blade installing knob in the @ direction to tighten the clamp. Blade installing knob Button Blade holder Roller 5. With the blade installing knob kept in this position, push it back down to i t s original position. NOTE : Occasionally lubricate the roller. Selecting the cutting action This tool can be operated with an orbital or a straight line cutting action. To change the cutting action, just turn the lever to the desired cutting action position. Refer to the table below to help determine the appropriate cutting action. I Position 0 Cutting action Straight line cutting action Applications For cutting mild steel, stainless steel and plastics. For clean cuts in wood and plywood. 1 I I1 I Small orbit cutting action Medium orbit cutting action I For cutting mild steel, aluminum and hard wood For cutting wood and plywood. For fast cutting in aluminum and mild steel. I 6 111 I Large orbit cutting action I For fast cutting in wood and plywood. Switch action For 4304T CAUTION : Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. To start the tool, simply pull the trigger. For continuous operation, pull the trigger and move the lock lever backward. To stop the tool from the locked position, pull the trigger fully, then release it. ILock lever Switch trigger For 4305T CAUTION: Before plugging in the tool, always check to see that the switch actuates properly. To start the tool, slide the switch lever forward. Slide the switch lever backward to stop. Speed adjusting dial The tool speed can be adjusted and maintained between 500 and 3, 000 strokes per minute by turning the adjusting dial. The dial i s marked 1 (lowest speed) to 6 (full speed). For 4304T Speed adjusting dial I For 4305T Speed adjusting dial Refer to the table a t right to Select the Proper speed for the workpiece to be cut. [. . . ] 8 - 1 9 3 - 30 mm thick 1118" - 1 ~ 1 / 8 " ) H 3 - 55 mm thick 1118'' - 2-118"l H No. 8-21 - 1 - 3 mm thick 13/64" - 1/8"l 3 - 6 mm thick 1118'' - 1/4"l 0. 5 - 2 mm thick (1164'' - 5/64, ') No. 8 - 2 2 - 1. 5 - 3 mm thick 11/16" - 118") U No. 8 - 2 3 - 3 - 6 mm thick (118" - 1/4'1 H 1 - 3 mm thick (3164'' - 118"I H No. [. . . ]