User manual MAKITA LS0713FL

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MAKITA LS0713FL. We hope that this MAKITA LS0713FL user guide will be useful to you.

Lastmanuals help download the user guide MAKITA LS0713FL.


Mode d'emploi MAKITA LS0713FL
Download
Manual abstract: user guide MAKITA LS0713FL

Detailed instructions for use are in the User's Guide.

[. . . ] 1 2 3 4 5 6 7 Frame Bolts Support Inner grooves (A) Outer grooves (B) Frame pipe Lock plate 8 9 10 11 12 13 14 Support plate (For LS0714 only) The smallest hole in the support Adjusting bolt Front holes in your tool base Front holes in the supports Bolt Nut 15 16 17 18 19 20 Fix plates Outer hole (a) Inner hole (b) The largest holes Outer frame Inner frame Read and thoroughly understand this manual and the instruction manual of the tool you use before performing the following. â· Before installing a tool on this stand, always switch off and unplug the tool. [. . . ] When the stand cannot be set up stable, turn the adjusting bolt at the foot of stand for proper stability. After adjustment, make sure that the stand and tool keep stable. Secure the feet of stand to the stable and level surface using holes in the fix plates with three hex bolts. CAUTION: When using the thicknesser or planer specified in this manual, set up the stand in the low position mode. Change the installation position of the lock plate from the outer hole (a) to the inner hole (b) and retighten the bolt firmly. Close the frame slightly, raise the support and detach the frame pipe from the inner grooves (A) in the support. While holding the frame on, widen the feet of frame carefully and fully. Adjust the position of the supports according to the distance of front holes in the base of the tool you use. Turn the stand so that the adjusting bolt at its foot or the corporate nameplate faces you. place the tool in the middle of the support. Thicknesser or planer model specified in this manual should be placed so that four holes of the tool base match the largest holes on the support of the stand. 7) Note: When the holes in the tool base do not align with those in the support, unlock the lock plate by raising it, readjust it for fine adjustment and push it down again to lock it. Secure the tool base to the support of the stand with four hex bolts and four nuts provided with the stand. Make sure that these four bolts are inserted from the underside as shown in the figure. [. . . ] All miter saw models specified in this manual should be placed so that two front holes of the tool base match the first front holes on the support. Note: When the holes in the tool base do not align with those in the support, unlock the lock plate by raising it, readjust it for fine adjustment and push it down again to lock it. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA LS0713FL

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA LS0713FL will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag