User manual MAKITA LS1018L ANNEXE 834

[. . . ] Stopper pin Bolts Blade guard Kerf board Screw Saw blade Blade teeth Left bevel cut Straight cut Right bevel cut Adjusting bolt Turn base Top surface of turn base Periphery of blade Guide fence Stopper arm Adjusting screw Miter scale Pointer Lock lever Grip Lever Arm Bevel scale Release button Locking screw Lock-off button 28. Switch trigger Hole for padlock Switch for laser Screw holding the laser unit box Dry cell Socket wrench with hex wrench on its other end Wrench holder Socket wrench Blade case Center cover Hex bolt Arrow Shaft lock Hex bolt (left-handed) Outer flange Ring Inner flange Spindle Dust nozzle Dust bag Fastener Support Sliding fence Clamping screw Sub-fence R Screws 54. Vise arm Vise knob Vise rod Vise plate Vise nut Holder 52/38° type crown molding 45° type crown molding 45° type cove molding Inside corner Outside corner Vise Spacer block Aluminum extrusion Horizontal vise (optional accessory) Holes Cut grooves with blade Triangular rule 0° adjusting bolt Left 45° bevel angle adjusting bolt Right 45° bevel angle adjusting bolt Screwdriver Brush holder cap Model Blade diameter Hole diameter For all countries other than European countries For European countries Max. Cutting capacities (H x W) with 260 mm in diameter Miter angle 0° 45° 60° (right) No load speed (min-1) Laser Type (LS1018L only) Dimensions (L x W x H) Net weight Bevel angle 45° (left) 50 mm x 310 mm 50 mm x 220 mm 0° 91 mm x 310 mm 91 mm x 220 mm 91 mm x 153 mm 45° (right) 31 mm x 310 mm 31 mm x 220 mm LS1018/LS1018L 255 mm - 260 mm 25. [. . . ] Proper workpiece support will help avoid blade pinch and possible kickback which may result in serious personal injury. Support workpiece over its entire length to avoid blade pinch and possible KICKBACK. Guide fence (SLIDING FENCES which are upper and lower fences) adjustment (Fig. Before operating the tool, make sure that the sliding fence is secured firmly. ⷠBefore bevel-cutting, make sure that no part of the tool, especially the blade, contacts the upper and lower fences when fully lowering and raising the handle in any position and while moving the carriage through its full range of travel. If the tool or blade makes contact with the fence this may result in kickback or unexpected movement of the material and serious personal injury. When performing bevel cuts, slide the sliding fence to the left and secure it as shown in the figure. Otherwise, it will contact the blade or a part of the tool, causing possible serious injury to the operator. This tool is equipped with the sliding fence which should ordinarily be positioned as shown in the figure. However, when performing left bevel cuts, set it to the left position as shown in the figure if the tool head contacts it. When bevel-cutting operations are complete, don't forget to return the sliding fence to the original position and secure it by firmly tightening the clamping screw. The use of the dust bag makes cutting operations cleaner and dust collection easier. To attach the dust bag, fit it onto the dust nozzle. When the dust bag is about half full, remove the dust bag from the tool and pull the fastener out. Empty the dust bag of its contents, tapping it lightly so as to remove particles adhering to the insides which might hamper further collection. Before operating the tool, make sure that the sub-fence R is secured firmly. 33) The sub-fence R can be removed from the right side of the guide fence. To remove the sub-fence R, loosen the screw which secures the sub-fence R and pull it out. follow the removal procedure in reverse to install it. When bevel-cutting operations are complete, don't forget to return the sub-fence R to the original position and secure it by firmly tightening the clamping screw. When cutting a thin workpiece, such as base boards, against the fence, always use the horizontal vise. The holders can be installed on either side as a convenient means of holding workpieces horizontally. [. . . ] Attempting a cut with a dull and /or dirty blade may cause kickback and result in a serious personal injury. This tool is carefully adjusted and aligned at the factory, but rough handling may have affected the alignment. If your tool is not aligned properly, perform the following: 1. After use, wipe off chips and dust adhering to the tool with a cloth or the like. [. . . ]