User manual MAKITA LS800D

[. . . ] Be sure that you understand their meaning before use. To avoid injury from flying debris, keep holding the saw head down, after making cuts, until For your safety, remove the chips, small pieces, etc. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 Battery cartridge Push button Socket wrench Wrench holder Blade case Stopper pin Bolts Hex bolt Center cover Safety cover (Safety guard) Arrow Shaft lock Hex bolt (left-handed) Outer flange Saw blade Inner flange Spindle Dust nozzle Dust bag Fastener Kerf board Left bevel cut 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 Straight cut Adjusting bolt Guide fence Turn base Periphery of blade Top surface of turn base Miter scale Pointer Grip Lock lever Lever Loosen Tighten Bevel scale Pointer Arm Vise rod Vise arm Vise knob Holder Holder assembly Vise knob 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 Base Vise shaft Projection Rods 12 Lock-off button Handle Switch trigger Lock lever Apply pressure in parallel with blade Set plate Screw Hex bolt Triangular rule Screw 45° bevel angle adjusting bolt 0° bevel angle adjusting bolt Sub arm Screw Limit mark Screwdriver Brush holder cap Due to our continuing program of research and development, the specifications herein are subject to change without notice. Note: Specifications may differ from country to country. [. . . ] After using the socket wrench, return it to the wrench holder. When the tool is shipped, the handle is locked in the lowered position by the stopper pin. release the stopper pin by lowering the handle slightly and pulling the stopper pin. This tool should be bolted with four bolts to a level and stable surface using the bolt holes provided in the tool's base. The use of the dust bag makes cutting operations clean and dust collection easy. to attach the dust bag , fit the bag's entry port over the dust nozzle. When the dust bag is about half full, remove the dust bag from the tool and pull the fastener out. Empty the dust bag of its contents, tapping it lightly so as to remove particles adhering to the insides which might hamper further collection. Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing the blade. This could cause serious injury to operator or others in the general vicinity of the tool. 3) To remove the blade, use the socket wrench to loosen the hex bolt holding the center cover by turning it counterclockwise. Raise the safety cover and center cover. 5) Press the shaft lock to lock the spindle and use the socket wrench to loosen the hex bolt (left-handed) clockwise. 6) To install the blade, mount it carefully onto the spindle, making sure that the direction of the arrow on the surface of the blade matches the direction of the arrow on the blade case. Install the outer flange and hex bolt, and then use the socket wrench to tighten the hex bolt (lefthanded) securely counterclockwise while pressing the shaft lock. This tool is provided with the kerf boards in the turn base. The kerf boards are factory adjusted so that the saw blade does not contact the kerf boards. before use , adjust the kerf boards as follows: First , remove the battery cartridge. Loosen the all screws (2 each on left and right) securing the kerf boards. Retighten them to the extent that the kerf boards can be easily moved by hand. Lower the handle fully and push in the stopper pin to lock the handle in the lowered position. After adjusting the kerf boards, release the stopper pin and raise the handle. [. . . ] If your tool is not aligned properly, perform the following: 1. Miter angle Loosen the grip which secures the turn base. Turn the turn base so that the pointer points to 0° on the miter scale. Then turn the turn base slightly clockwise and counterclockwise to seat the turn base cozily in the 0° miter notch. [. . . ]