User manual MAKITA PS344

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MAKITA PS344. We hope that this MAKITA PS344 user guide will be useful to you.

Lastmanuals help download the user guide MAKITA PS344.


Mode d'emploi MAKITA PS344
Download
Manual abstract: user guide MAKITA PS344

Detailed instructions for use are in the User's Guide.

[. . . ] Be sure that you understand their meaning before use. Cutting means continues to run after the motor is switched off. Cd Ni-MH Li-ion battery pack together with household waste material!In observance of European Directive 2002/96/EC on waste electric and electronic equipment, 2006/66/EC on batteries and accumulators and waste batteries and accumulators and their implementation in accordance with national laws, electric equipment and battery pack that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility. [. . . ] If the cartridge does not slide in easily, it is not being inserted correctly. iMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CARTRIDGE ENC007-7 1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F). Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. 15) Adjust the three pin position so that these pins are lined up at right angle in relation to the basic alignment line on the tool housing. 16) 13 ASSEMBLY CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Installing or removing blade cover CAUTION: • Be careful not to contact the shear blade when installing or removing the blade cover. Contacting the shear blade may cause personal injuries. 6 & 7) Slide the blade cover from the tool’s side until the shear blade completely hides itself and then push in it lightly towards the tool from the front. To remove the blade cover, take the above installation procedure in reverse. Installing or removing base frame CAUTION: • Before installing or removing base frame, be sure to install the blade cover. € When installing or removing base frame, take care that your fingers are not be pinched between the tool and base frame. 8) To remove the base frame, upset the tool and take it out of the groove grabbing its bottom. 9) To install the base frame, fit the protrusion of base frame near the change lever into the hole for the sheared grass height setting. With the base frame so fitted, pull the lower Fit the crank with its recessed part facing upwards onto the pins. [. . . ] Hedge trimming operation with optional hedge shear blades Noise ENG905-1 The typical A-weighted noise level determined according to EN60745: Sound pressure level (LpA): 74 dB (A) Uncertainty (K): 2. 5 dB (A) The noise level under working may exceed 80 dB (A). 5 m/s2 ENG901-1 Installing or removing chip receiver (optional accessory) CAUTION: • Always be sure that the tool is switched off and the battery cartridge is removed before installing or removing chip receiver. NOTE: • When replacing the chip receiver, always wear gloves so that hands and face does not directly contact the blade. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA PS344

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA PS344 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag