User manual MAKITA SJ401

[. . . ] 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Installing Pin End Blade . . . . . . . . . . . . . . . . . . . . . . . . . 10 Installing Plain End Blade . . . . . . . . . . . . . . . . . . . . . . . 11 11 Removing Plain End Blade . . . . . . . . . . . . . . . . . . . . . . [. . . ] Loose Parts Bag Containing the following parts: Blade Change Rod. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hex Wrench "L" . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Saw blade 1 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Getting To Know Your Scroll Saw \ Lamp support 7. Table Lock Knob Base & 2 & 9. Hold Down Foot Blade Tension Lever 11. Sawdust Ejection Port 6 Getting To Know Your Scroll Saw This versatile heavy-duty scroll saw is great for making toys, puzzles, games, artwork, and jewelry, and because of its cutting capacity, it is a handy do-it-yourself tool. It cuts wood and plastic up to 2 inches thick. 6. Blade Tension Lever Allows you to loosen or tighten the blade tension by rotating the lever. 1. Blade Storage Case Your scroll saw is equipped with a blade storage area located on the side of the saw. The blade storage area conveniently stores the blade set screws, allen wrenches and both pin and plain end blades. You can open the case with pressing the top. 7. Install the blade through the insert opening. Engage the pin into the "V" notch of the lower blade holder. w 4. Pull up on the blade and engage the upper pin in the Lower Blade Holder notch of the upper blade holder. Blade Holder 5. Flip tension lever down to horizontal position to lock in tension. NOTE: For your own need, turn blade tension lever clockwise until blade is tensioned. 10 Assembly & Aausting INSTALLING PLAIN END BLADES NOTE: For plain end blades, the set screw of the blade holders needs to be used. The set screws are supplied in the loose parts bag. 1. Install blade with the tension lever in vertical position. 3. Install the new blade through the insert hole in the table, and into the lower blade holder. Position the lower end of the blade in the lower blade holder. Tighten the plain blade set screw using the "L" wrench. 5. Use the same procedure to install the blade into the upper blade holder. Tighten the blade set screw using the "L" wrench, while holding the blade change rod in position. 6. [. . . ] Squirt a generous amount of SAE20 Oil around the shaft end and bronze bearing. Let the oil soak in overnight in this position. Next day repeat the above procedure for the opposite side of the saw. Arm Bearings Lubricate the arm bearings after 10 hours of use. Re-oil after every 50 hours of use or whenever there is squeak coming from the bearings. WIRING DIAGRAM 15 Content Pants 16 Part No. Description Part No. Description 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 2 1 22 23 24 25 26 27 28 29 30 3 1 Base Screw and Washer (4) Body Hose Plate Cover Blade Storage Case Pull Nail (2) Screw (2) Blade Motor Screw and Washer (3) Power Cord Spacer Counterweight Set Screw Hex Socket Bolt Spring Washer Flat Washer Hold Down Block Support Rod Set Screw Hold Down Foot Hex Socket Bolt (3) Blade Support & Guard Flat Washer (3) Dust Blower Pin, Spring Knob Bushing Set Cover Screw (8) Bushing (2) 32 33 34 35 36 37 38 39 40 4 1 42 43 44 45 46 47 48 49 50 5 1 52 53 54 56 57 58 59 60 6 1 Board Cover Screw (2) Control Board Switch, Washer and Nut Control Knob Gasket Switch Cover Lock Post Nut Screw (2) Switch Case Screw (4) Ext. [. . . ]