User manual MAKITA UH4261

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual MAKITA UH4261. We hope that this MAKITA UH4261 user guide will be useful to you.

Lastmanuals help download the user guide MAKITA UH4261.


Mode d'emploi MAKITA UH4261
Download
Manual abstract: user guide MAKITA UH4261

Detailed instructions for use are in the User's Guide.

[. . . ] Nut Shear blade Hooks Fit the hooks into groove Grooves Press the hooks on both sides Unlock the hooks Model Blade length Strokes per minute (min-1) Overall length Net weight Safety class UH4261 420 mm 1, 600 821 mm 2. Due to our continuing programme of research and development, the specifications herein are subject to change without notice. ⷠSpecifications may differ from country to country. ⷠWeight according to EPTA-Procedure 01/2003 Symbols END220-4 The following show the symbols used for the equipment. [. . . ] ⷠPut the blade cover on the shear blades before adjusting or checking function on the tool. For your safety, this tool is equipped with a triple switching system. to turn on the tool , press switch trigger B and press switch trigger A or C at the same time. Release either one of the two pressed switch triggers to turn off. The sequence of switching is unimportant as the tool only starts when both switches are activated. To trim the hedge straight, pull switch triggers A and B. Cut upwards with both hands pull the switch triggers B and C and move it in front of your body. Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Attach the hook about 100 ­ 200 mm from the extension cord connector. Do not attach the holder of waist cord hook to other than the extension cord. Do not attach it in a position closer to the tool beyond the hook complete. Attach firmly one hook of the hook complete to the tool's cord and the other hook of hook complete to the extension cord. Working with the tool with a sole hook only attached may cause an accident and injury. Using the waist cord hook helps to minimizing a risk of cutting off the extension cord unexpectedly caused by the loose extension cord. 5 & 6) Press in or pull out the cord through the opening of the holder. cAUTION: · Do not force the opening of the holder. To cut a hedge top evenly, it helps to tie a string at the desired hedge height and to trim along it, using it as a reference line. 12) Attaching the chip receiver (accessory) on the tool when trimming the hedge straight can avoid cut off leaves' being thrown away. 13) To cut a hedge side evenly, it helps to cut from the bottom upwards. 14) Trim boxwood or rhododendron from the base toward the top for a nice appearance and good job. Always be sure that the tool is switched off and unplugged before installing or removing chip receiver. nOTE: · When replacing the chip receiver, always wear gloves so that hands and face does not directly contact the blade. [. . . ] 9 & 10) As a basic operation, tilt the blades towards the trimming direction and move it calmly and slowly at the speed rate of 3 ­ 4 seconds per meter. Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Clean out the tool by wiping off dust with a dry or soapdipped rag. Smear the blade before and once per half an hour during operation using machine oil or similars. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA UH4261

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA UH4261 will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag