User manual MARANTZ MD2020

[. . . ] The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] For each station, you can memorize the frequency and reception mode if desired. 3. 3. 1. 3. Switch the remote controller to TUNER mode. Press the < / > button on the remote controller to display 002. Each time the T-MODE button is pressed, the TUNER mode changes and the mode is displayed on the FL display. AUTO PRESET MEMORY This function automatically scans the FM and AM band and enters all stations with proper signal strength into the memory. MANUAL TUNING 1. PURE DIRECT M-DAX 3. AV PRE TUNER MD2020 2. UP HDMI 2. 4. 2. Analog / Digital Auto Mode T-MODE:DIG-AT For listening to HD Radio stations. See p. 52 for more information on HD Radio technology. INPUT SELECTOR 2. 5. AV PRE TUNER MD2020 UP PURE DIRECT HDMI M-DAX DOWN INPUT SELECTOR VOLUME SURROUND MODE AUTO ZONE ZONE SPEAKER MENU EXIT BAND T-MODE MEMORY CLEAR 5. 1. 6. Switch the remote controller to TUNER mode. Press the < / > button until 001 is displayed. Press the GUIDE button on the remote controller, display will show "FREQ----". lnput your desired station's, frequency with the ten numbered keypad on the remote controller. When the desired preset station is received, cancel the preset scan operation by pressing the CLEAR button or P-SCAN button on the remote controller. 4. NAMES AND FUNCTION PURE DIRECT INPUT SELECTOR SURROUND MODE 3. AV PRE TUNER MD2020 M-DAX 2. 5. Up to 10 channels can be displayed at a time. If there are more than 10 channels, press P-INFO button on the remote controller once more to display the next page. The list display will disappear automatically in 5 seconds. 4. CLEAR 4. 3. CONNECTIONS SETUP TROUBLESHOOTING OTHERS (Using the unit) VOLUME AUTO ZONE ZONE SPEAKER MENU EXIT BAND T-MODE MEMORY PURE DIRECT THX 7. 1CH INPUT 3. 5. 1. TOP M-DAX DISPLAY Select the desired preset station by pressing the 1 or 2 cursor buttons on the front panel. CLEARING STORED PRESET STATIONS You can remove preset stations from the memory using the following procedure. PHONES SETUP MIC ENTER (Using the remote controller) PRESET CHANNEL LIST DISPLAY A complete list of the broadcast channels stored in this unit can be displayed. 1. 2. Switch the remote controller to TUNER mode. Press the 1 or 2 cursor buttons to tune in the deseired preset station. Or enter the preset station number with the numeric buttons. 2. AV PRE TUNER MD2020 UP PURE DIRECT HDMI M-DAX 3. (Using the unit) DOWN 1. 4. BASIC OPERATION ADVANCED OPERATION REMOTE CONTROLLER Tune into the radio station you desire (Refer to the "MANUAL TUNING" or "AUTO TUNING" section). Press the MEMORY button on the front panel. [. . . ] Audyssey MultEQ is the only technology that can achieve room correction for multiple listeners in a large listening area. It does so by combining the data collected at several points in the room from each loudspeaker and then applying correction that minimizes the acoustical effects of the room and is matched to the frequency resolution of human perception (known as psychoacoustics). Furthermore, MultEQ correction is applied both in frequency and time domains and so there are no artifacts (such as smearing of sound or modal ringing)that are sometimes associated with traditional methods of room equalization. In addition to correcting frequency response problems over a wide listening area, Audyssey MultEQ provides a completely automated sound system set-up process. [. . . ]