User manual MARANTZ NR 1602

[. . . ] SVENSKA NEDERLANDS Español Italiano Français Deutsch ENGLISH AV Surround Receiver NR1602 v CD-ROM Getting Started Erste Schritte Mise en route Guida introduttiva Antes de empezar Aan de slag Att komma igång Explains how to easily install, connect and setup a 7. Open the included CD-ROM on your computer for detailed operating instructions. ZzD&M Holdings is striving to be a paperless company in order to help preserve the environment. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. [. . . ] Next, disconnect the connection cables to other system units before moving the unit. € About care • Wipe the cabinet and control panel clean with a soft cloth. € Follow the instructions when using a chemical cleaner. € Benzene, paint thinner or other organic solvents as well as insecticide may cause material changes and discoloration if brought into contact with the unit, and should therefore not be used. Playback Accessories Check that the following parts are supplied with the product. NnIllustrations Note that the illustrations in this manual is for explanation purposes and may differ from the actual unit. 1 e r nnAbout the CD-ROM (Getting Started / Owner’s manual) You need to have Adobe Reader® installed on your computer to view the owner’s manuals on the CD-ROM. Click the Adobe Reader® banner in the CD-ROM menu to install the Adobe Reader® (for Windows). Y u i 1 ENGLISH Deutsch Français Italiano Español NEDERLANDS SVENSKA РУССКИЙ POLSKI TÜRKÇE Preparing the Setup Wizard This section describes how to prepare the Setup Wizard before use. NnDo not plug the power plug of the main unit into the wall socket until these preparations are complete. NnSpeaker connections are performed using the Setup Wizard. What you need for this step Speaker (sold separately) Speaker cable (sold separately) 1 Place and layout speakers Connect the speaker cables to the main unit using the Setup Wizard. Before installing the speakers, connect the speaker cables to the speakers. For details on how to connect the speaker cables, see the speaker instruction manual. 1-channel (Surround back speaker) installed • Prepare enough for the number of speakers you will use. 1-channel installed SL SR SBR FL FL SW C z1 z3 FR SW C z1 FR Subwoofer (with built-in amplifier) (sold separately) Audio cable (sold separately) z2 z2 SL SR SL SR TV (sold separately) HDMI cable (sold separately) SBL Listening position SBR Listening position z1 22˚ – 30˚ z1 22˚ – 30˚ z2 90˚ – 110˚ z3 135˚ – 150˚ z2 120˚ Remote control unit / R03/AAA batteries (supplied) Setup microphone (supplied) Power cord (supplied) FL FR C SW SL SR SBL SBR Front speaker (L) Front speaker (R) Center speaker Subwoofer Surround speaker (L) Surround speaker (R) Surround back speaker (L) Surround back speaker (R) • Install the surround speakers in a position 60 to 90 cm higher than ear level. surround speaker 60 – 90 cm Front speaker Surround back speaker (When 7. 1-channel installed) • Point slightly downwards GViewed from the sideH 2 TÜRKÇE POLSKI РУССКИЙ SVENSKA NEDERLANDS Español Italiano Français Deutsch ENGLISH 2 C  onnect this unit to the television using an HDMI cable (sold separately) 3 T urn the television power on, and switch the video input to this unit (HDMI input) Preparation NOTE If this unit is connected using cables other than the HDMI cable, the Setup Wizard will not be displayed. For details on how to operate the television, see the television instruction manual. Setup Wizard HDMI IN (ARC) q Power on w Switch the input to this unit (HDMI input) 4 Insert the provided batteries into the remote control unit  q Remove the rear lid in the direction of the arrow and remove it. Playback w Load the two batteries properly as indicated by the marks in the battery compartment. R03/AAA e Put the rear cover back on. [. . . ] BD M-XPort DVD SAT TUNER GAME CD NET/USB TV When an input source select button (BD, DVD, SAT, TV, CD, NET/USB, TUNER or M-XP) is pressed once, the unit switches to device selected by the operating mode of the remote control. If the input source select button is then pressed again twice, the input source for the unit is switched. € When 21 is pressed, the input source of this unit is switched to “NET/USB” and the connected iPod is automatically played (vm page 26 “iPod play function”). NnUsing the knob on the main unit [ ] Move [ENTER] Enter Playback q Press 3. [. . . ]