User manual MARANTZ PD4292D

[. . . ] R Model PD4292D User Guide Plasma Monitor PD4292D-1 1 00. 10. 4, 3:08 PM IMPORTANT INFORMATION PRECAUTIONS Please read this manual carefully before using your marantz 42 inch Plasma Monitor and keep the manual handy for future reference. Warnings and Safety Precaution The SLIM SERIES PLASMA MONITOR PD4292D is designed and manufactured to provide long, trouble-free service. No maintenance other than cleaning is required. Use a soft dry cloth to clean the panel. Never use solvents such as alcohol or thinner to clean the panel surface. [. . . ] To maintain display quality, use a cable with a quality prescribed by DVI standards that is within 5 meters in length. 21 PD4292D-2 21 00. 10. 4, 3:10 PM External Speaker Connections RGB 3 (Digital RGB) RGB 1 SPEAKERS MUST HAVE MORE THAN 7WATT RATING IMPEDANCE 6 OHM LEFT R/CR/PR RGB2/ DVD2/ HD2 ­ + LEFT G/Y B/CB/PB HD VD ­ + RIGHT AUDIO 1 RIGHT EXTERNAL CONTROL REMOTE CONTROL CONTROL LOCK ON/ OFF L(MONO) R VIDEO 1 VIDEO 2 VIDEO 3 AUDIO 2 L(MONO) R Y CB/CR AC IN AUDIO 3 PB/PR L(MONO) R External speakers may be connected to the plasma monitor to reproduce sound from VIDEO, DVD or RGB signal sources. External speakers may be connected directly to the SPEAKERS terminals or indirectly by connecting a stereo system amplifier to the audio outputs. CAUTION: Unplug the plasma monitor and all connected components before connecting external speakers. Use only speakers with 6-ohm impedance and a power output rating of 7 watts or more. To connect external speakers directly to the plasma monitor: 1. Press down the tabs below the SPEAKERS terminals, insert the speaker wire and release the tab to secure the speaker wire connection: [a] Connect the right speaker (located at right side of the monitor when viewed from the front) positive (+) wire to RIGHT +. [b] Connect the right speaker negative (­) wire to RIGHT -. [c] Connect the left speaker negative (­) wire to LEFT­. [d] Connect the left speaker positive wire (+) to LEFT+. 22 PD4292D-2 22 00. 10. 4, 3:10 PM Connecting Your PC Or Macintosh Computer Connecting your PC or Macintosh computer to your Plasma monitor will enable you to display your computer's screen image for an impressive presentation. The Plasma monitor supports the signals described on page 50. To connect to a PC, Macintosh or compatible graphics adapter, simply: 1. Turn off the power to your Plasma monitor and computer. If your PC does not support XGA/SVGA/VGA you will need to install an XGA/SVGA/VGA graphics board. Consult your computer's owner's manual for your SXGA/XGA/ SVGA/VGA configuration. If you need to install a new board, see the manual that comes with your new graphics board for installation instructions. The Plasma monitor provides signal compatibility with VESA 1280 1024@60Hz (SXGA). However, it is not recommended to use this resolution due to image readability on the monitors 853 480 native pixel resolution panel. Use the signal cable that's supplied to connect your PC or Macintosh computer to the Plasma monitor. For Macintosh, use the supplied monitor adapter to connect to your computer's video port. Turn on the Plasma monitor and the computer. If the Plasma monitor goes blank after a period of inactivity, it may be caused by a screen saver installed on the computer you've connected to the Plasma monitor. When using a Macintosh with the Plasma monitor, the following three display standards are supported using the included Macintosh adapter : 13" fixed mode 16" fixed mode 19" fixed mode The 13" fixed mode is recommended for the Plasma monitor. Connecting Your VCR Or Laser Disc Player Use common RCA cables (not provided) to connect your VCR or laser disc player to your Plasma monitor. Turn off the power to your Plasma monitor and VCR or laser disc player. Connect one end of your RCA cable to the video output connector on the back of your VCR or laser disc player, connect the other end to the Video input on your Plasma monitor. [. . . ] It is almost impossible to have zero pixel defects, even using the most advanced technology. This is not a problem only for Marantz, but all Plasma manufacturers. Therefore we have to note that the warranty does not cover the Plasma display panel for pixel defects. We appreciate your understanding. What is covered? 1) Warranty coverage begins the day you purchase your Plasma Television, and continues for a period of one year. [. . . ]