User manual MARANTZ RC-2000MKII

[. . . ] ENGLISH CONTENTS ENGLISH: INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 BUTTON NAMES AND FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 3 RC2000 Mk w BASIC OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . 11 PROGRAMMING THE RC2000 Mk w . . . . . . . . . . . . . . . . . . . . . . [. . . ] You will see "DIR CLR" indicated in the LCD window. At that point, if you press "OK" in the cursor keys, you will erase all four pages in that particular direct function. After clearing, the RC2000 Mk w will restore any factory programmed codes. If you do not wish to clear the pages, press any other key other than the "OK" button. Erasing the memory assigned to a particular button: First check the current function. (In this example, let us assume that it is LD. ) Press and hold the "CLEAR" button !4 and press the button that you wish to erase 2 times. The code previously learned by that button will be erased, and will then be either empty, or the original factory provided RC-5 codes will re-appear in its place. TUNER CD TAPE AUX AMP 3. POWER SOURCE ON ON/OFF CLONE MACRO OFF MODE MACRO LEARNING REMOTE CONTROL RC2000MK MACRO Press the MODE button to switch to USE. Note: The status and direct mode names of each page that are not rewritten remain without being erased. CH VOL How to clear (erase) the memorized codes (and any re-written names): The RC2000 Mk w has a high capacity RAM, which ordinarily will allow the learning of several hundred remote codes (and their associated new names, if desired). However, due to the fact that some remote codes occupy more memory space than others, it is possible that the available RAM fills up completely, and the "FULL" indicator appears in the LCD window. In this case, it will not be possible to learn any new remote codes without first deleting some or all of the previously learned remote codes and/or re-written names. There are 4 ways to erase learned remote codes from memory: 1 4 7 M 2 5 8 0 3 6 9 OSD GUIDE MUTE OK C While holding the CLEAR button depressed, press PLAY twice. The LD PLAY code is cleared and the original RC-5 code is recalled. 19 20 4. Erasing the memory assigned to each function command set: All codes and names, which were previously memorized for each of the functions (such as TV, LD, VCR, etc. ), can be erased. Press and hold the CLEAR button !4, and press the function button that you want to erase 2 times. You will see the "FNC - CLR?" (function - clear?) indication in the LCD window (see Figure 5). If you wish to go ahead and clear all of the memorized codes for that function button, press the "OK" button within the cursor keys !6. After clearing the memory contents for that function, the RC2000 Mk w will restore any factory programmed RC-5 codes for the function, if any, or will simply be empty. DSS MD TV LD DVD VCR 7 M 8 0 9 OSD GUIDE MUTE C LEARN While holding the CLEAR button depressed, POWER SOURCE ON ON/OFF CLONE MACRO OFF MODE 1 MACRO 2 3 4 MACRO LEARNING REMOTE CONTROL RC2000MK Figure 6 1 3 pressing simultaneously displays [ALLCLR?]. NOTE: The RC-5 codes as supplied from the factory cannot be erased from memory, but they can be replaced with different codes as you wish. By now, you have learned how to memorize codes from other brands of components, including changing the various function, status, and direct function names. TUNER CD TAPE AUX AMP LOW LEARN CH VOL 1 4 7 M 2 5 8 0 3 6 9 OSD GUIDE MUTE 1 OK 2 3 4 Figure 5 C While holding the CLEAR button depressed, press LD twice; [FNC-CLR?] will be displayed. If you want to cancel the memory clear operation, do not press the "OK" button, but instead simply touch any other button. When you clear all the commands associated with a function button, all of the learned direct function commands (D-1 through D-8, pages 1 through 4) are cleared as well. ¼ Before continuing on to the more advanced RC2000 Mk w programming techniques, you may wish to continue "teaching" the RC2000 Mk w remote control with any or all other commands for other components in your system. When you feel you've transferred as many different commands from other components into the RC2000 Mk w as you'd like, and possibly changed some or all of their names as well, then feel free to proceed to the next section. ¼ The all-clear operation takes about 15 seconds after the OK button is pressed. ADVANCED PROGRAMMING TECHNIQUES Macro mode: The word "macro" is used to describe a series of specific steps carried out in sequence. For example, a word processing program can use macros to carry out common repetitive typing tasks. [. . . ] REC 1 TP-1 2 3 4 5 REC PAUS STOP TP-2 7 T-S 8 ENT 4. REC 1 TAPE 2 3 4 5 REC PAUS STOP MD 6 REC 7 PAUS 8 STOP 3. RDS 1 STM *for REST only 2 AF 3 PTY 4 DISP 5 6 7 8 DWR 6 REC 7 PAUS 8 STOP TAPE 1. MODE selects WAVE RANGE of DSR 1 2 3 4 5 6 7 8 TP-A TP-B DIR TIME TRAY AMS REC PAUS selects tape deck A selects tape deck B auto-reverse direction time display tray open/close automatic music scan record pause 39 40 TV 1. [. . . ]