User manual MARANTZ SA7003

[. . . ] SVENSKA ITALIANO ESPAÑOL NEDERLANDS DEUTSCH FRANÇAIS ENGLISH Super Audio CD player SA8003 SA7003 ENGLISH WARRANTY For warranty information, contact your local Marantz distributor. RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz. IMPORTANT When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase. [. . . ] In the stop mode, press 7 STOP button once. Program can also be cleared by pressing 0 OPEN/ CLOSE button to open the disc tray. tO add tracKs tO prOGram Tracks can be added to the end of program when program is remaining ("PROG" indicator is lighting up) and in stop mode. please Be careFul aBOut tHe FOllOWING matters · When programming 1st through 9th tracks in a disc that has over 10 tracks by using numeric buttons. For instance, programming the 3rd track after programming the 1st track, press 3 button more than approximately 1. 5 seconds after 1 button is pressed. When a program is finalized, the time is updated. Once you find a song that you want to listen to, press the AMS button again or press the 2 button. The PLAY indicator lights up and normal playback resumes from the current track. Note: AMS Play cannot be conducted while the unit is in PROGRAM mode. CD layer 2. Press the S. MODE button during playback. The currently selected layer or area is shown on the display. (CD or Super Audio CD) If S. MODE button is pressed again, the playback is stopped, and the layer or area will be switched to new one. When you want to listen at that area, press 2 button again. The playback will be started. 15 OtHers trOuBlesHOOtING This feature is convenient for searching where your favorite track is. If the AMS button is pressed while a track is stopped, the PLAY indicator "2" flashes, and the first ten seconds of each track on the disk will be played starting from the first track. Also, if the AMS button is pressed during playback, the PLAY indicator "2" flashes, and the program jumps to the next track after approximately 10 seconds elapses on the display time. remOte cONtrOller applIcatION OperatION OperatION adVaNced cONNectIONs Note: AMS BasIc OperatION Total programmed number Total playing time of programmed tracks searcHING YOur FaVOrIte tracKs (ams (autOmatIc musIc scaN) plaY) S. MODE BasIc cONNectION · Likewise, when programming a track at 10th or after. For example, to program 13th track, press 3 button within approximately 1. 5 seconds after 1 button is pressed. · When programming a track in a disc that has less than 9 tracks. For instance, to program the 5th track after 4th track has been programmed, press 5 button more than approximately 0. 5 second after 4 button is pressed. sWItcHING sOuNd mOde (super audIO cd) Please set Start Sound Mode to "SA-CD" (see page 16). Names aNd FuNctIONs applIcatION OperatION (cd OperatION) ENGLISH applIcatION OperatION (cd OperatION) sWItcHING "start sOuNd mOde" The Start Sound Mode can be switched over in the following hierarchical scheme. SA-CD Mode SA-CD* CD * Default setting Names aNd FuNctIONs BasIc cONNectION BasIc OperatION adVaNced cONNectIONs remOte cONtrOller applIcatION OperatION OperatION trOuBlesHOOtING OtHers WHeN start sOuNd mOde Is sWItcHed tO cd · At this time, if a Super Audio CD hybrid layer disk is inserted, the CD layer is read. · Sound Mode cannot be switched even if the S. MODE button on the remote control is pressed. · If a disk with only a Super Audio CD area is inserted, the Super Audio CD layer is read. settING tHe dIGItal Output The settings can be made using the remote control. The settings are retained even if the power is turned off so that you can always hear tracks played the way you want. Use the same procedures to change the settings again. The settings can be changed when the track is stopped. 2. 4. WHeN start sOuNd mOde Is sWItcHed tO sa-cd (deFault mOde) · At this time, if a Super Audio CD hybrid layer disk is inserted, the Super Audio CD layer is read. [. . . ] · This unit can play CD format, video CD format, and CD-R/CD-RW discs which contain WMA/ MP3 music data. However, some discs may have problems such as unable to play, noise or sound distortion. · This device is exclusively a playback device. · As the playback of a CD-RW disc necessitates partial change of the player setup, it may take longer time for reading the TOC information than when an Audio CD or CD-R disc is played. [. . . ]