User manual MARANTZ SR4002

[. . . ] Model SR4002/SR5002 User Guide AV Surround Receiver ENGLISH WARRANTY For warranty information, contact your local Marantz distributor. RETAIN YOUR PURCHASE RECEIPT Your purchase receipt is your permanent record of a valuable purchase. It should be kept in a safe place to be referred to as necessary for insurance purposes or when corresponding with Marantz. IMPORTANT When seeking warranty service, it is the responsibility of the consumer to establish proof and date of purchase. [. . . ] Microphone connection check: MIC CHECK Ambient noise measurement: AMBIENT NOISE Speaker connected/not connected check: SPEAKER CHECK Speaker output level check: SPEAKER LEVEL Distance from speaker (delay time) check: SPEAKER DISTANCE Speaker characteristics check: SPEAKER SIZE · About surround back speakers : When the surround back speaker is set to NONE in the SPEAKER SETUP, it is skipped in the AUTO setup. To use the surround back speaker, set it to YES by MANUAL setup before using the MRAC feature. · The MRAC feature is available except in the following modes. - 7. 1 CH INPUT - PURE-DIRECT - SOURCE DIRECT Notes: · If MRAC is started with both speaker settings A and B off, it will enter CANCEL mode without displaying an ERROR on the screen. When this happens, check the SPEAKER setting. · The measured speaker distance may differ from the actual distance from speakers. Nevertheless, the measured value is suitable for the speakers. · To make changes to individual speakers, select 2. SPEAKER SETUP on the SETUP MAIN MENU, then select MANUAL for 2-1 SPEAKER SETUP. · The included microphone is designed specifically for this receiver. Other microphones do not guarantee suitable measurement results. Use the included microphone to conduct measurements. · During measurement, press the ENTER or EXIT button to cancel measurement. · In some rooms, an error may occur during auto speaker setup or it may not be possible to set Speaker distance correctly because of room acoustics. In such case, set the speaker distance by MANUAL setup. · Please set any THX Certified speakers manually to "Small" and the crossover to "80 Hz" after Auto setup operation. · When only HDMI components are connected, OSD will not be displayed. Error Indications During Measurement If trouble occurs during measurement, an error message is displayed on the monitor screen and FL display. Those errors and their remedies are described below. The message appearing on the FL display is given in ( ). MIC SETUP ERROR (MIC SET ERROR) The microphone (MC-10) is not properly connected. AMBI NOISE ERROR (AMBI NOISE ER) Measurement cannot be done correctly because of excessive ambient noise. [. . . ] 2005, 2009, 2020, 2035, 2057 Sampo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2008, 2012, 2022, 2024, 2027 Sanyo . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2050, 2052 Sharp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2044, 2045 Sherwood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2051 Sony . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2001, 2013, 2059 Toshiba . . . . . . . . . . . . . . . . . . . . . . 2004, 2008, 2026, 2028 Yamaha . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2046, 2060 Zenith . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]