User manual MARANTZ SR7500

[. . . ] Model SR7500/SR8500 User Guide AV Surround Receiver CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. IMPORTANT SAFETY INSTRUCTIONS READ BEFORE OPERATING EQUIPMENT This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of. Read Instructions ­ All the safety and operating instructions should be read before the product is operated. [. . . ] When the video equipment is connected by component terminal, connect the monitor and SR7500 by the component terminal. · This function is unavailable for the REC out terminal. · This function is unavailable for the still picture, fast forward and reverse playing of the video component. · If, while attempting to use the video convert feature, the SR7500 cannot synchronize with the display device, "NO SIGNAL" appears on the monitor, or noise is generated, this feature cannot be used. All of these signs are caused by equipment incompatibility; there is nothing wrong with the SR7500. In such case, set VIDEO CONVERT in the PREFERENCE menu to DISABLE. Also, connect the video input signal to the display device via the MONITOR OUT terminal under VIDEO and the S-video input signal to the display device via the MONITOR OUT terminal under S-VIDEO. Notes of OSD menu: · The setup menu can be displayed through all video out (COMPONENT, S-VIDEO, VIDEO). volume setting) are displayed through all video out when the VIDEO CONVERT function are set ENABLE. Note: No setting information is displayed when the signal is emitted from the COMPONENT IN to COMPONENT OUT. volume setting) are displayed through the S-VIDEO or VIDEO out when the VIDEO CONVERT function are set DISABLE. When the S-VIDEO and VIDEO outputs are used simultaneously, the setting informations are displayed through the S-VIDEO out only. VOLUME CH VOL EAK GHT ATT EQ ANALOG DIGITAL SURROUND DIGITAL L C R AAC PCM SL LFE S SR DOWN UP OK AUX 1 INPUT DIGITAL S-VIDEO VIDEO L AUDIO R LIP. SYNC PREV GUIDE MENU TEST CH. SEL MUTE EXIT SURR 1 7 1CH 2 ATT 3 SPK-AB Adjust the volume to a comfortable level using the VOLUME control knob on the front panel or VOL / buttons on the remote. To increase the volume, turn the VOLUME knob clockwise or press VOL button on the remote, to decrease the volume, turn counterclockwise or press VOL button on the remote. SELECTING THE SURROUND MODE Example: AUTO SURROUND M AV SURROUND RECEIVER SR7500 D1 INPUT SELECTOR D2 Notes: · The volume can be adjusted within the range of ­ to 18 dB, in steps of 1 dB. · However, when the channel level is set as described on page 20, if the volume for any channel is set at +1 dB or greater, the volume cannot be adjusted up to 18 dB. (In this case the maximum volume adjustment range is "18 dB - Maximum value of channel level) DISP SLEEP MULTI AUTO TUNED DIRECT D3 AUTO SURR Example: Monitor is connected with the component. STANDBY AV SURROUND RECEIVER SR7500 D4 USE PAGE 1234 D5 POWER ON/STANDBY PHONES CH TUNER ENTER VOL CD CD-R MD ADJUSTING THE TONE (BASS & TREBLE) CONTROL M TAPE AUX1 AUX2 AMP LIGHT VIDEO or S-VIDEO or component Monitor is connected with the video or S-video. AV SURROUND RECEIVER SR7500 1 RC8500SR Learning Remote Controller 2 D1 D2 component D3 ENTER (Using the SR7500) To select the surround mode during playback, press the AUTO button on the front panel. (Using the remote control unit) To select the surround mode, press the AMP button and press the > button until PAGE1 is displayed. Press the AUTO (D1) button. D4 USE PAGE 3 D5 CH TUNER CD CD-R VOL MD TAPE AUX1 AUX2 AMP LIGHT 1 RC8500SR Learning Remote Controller 2 VIDEO or S-VIDEO AV SURROUND RECEIVER SR7500 VIDEO or S-VIDEO During a listening session you may wish to adjust the Bass and Treble Control to suit your listening tastes or room acoustics. ENTER DVI-D INPUT (SR8500 only) When DVI-D is set as the input source, monitor output is DVI-D as well. component VIDEO or S-VIDEO 24 (Using the remote control unit) To adjust the tone, press the AMP button and press the > button PAGE3 is displayed. To adjust the bass effect, press BASS+ (D2) or BASS­ (D3). To adjust the treble effect, TREB+ (D4) or TREB­ (D5). Note: · The tone control function can work in the AUTO Surround, Stereo, Dolby Pro Logic IIx , DTS, DTS-ES, and Multi Ch. Stereo mode. OFF 90 10 80 20 70 30 60 40 50 The sleep time will be shown for a few seconds in the display on the front panel, and it will count down until the time has elapsed. When the programmed sleep time has elapsed, the unit will automatically turn off. Note that the SLEEP indicator on the display will illuminate when the Sleep function is programmed. [. . . ] 33. 1 lbs (15. 0 kg) (SR8500) ACCESSORIES Remote Control Unit RC8500SR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Microphone MC-10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 AAA-size batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 FM Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]